Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

YamahaWolverine

2003 Yamaha Wolverine - MPH Question

Recommended Posts

So I was reading and a stock 2003 wolverine 350 should top out at 55 MPH and mine only does 44? What could be dragging it down? Any ideas appreciated. Btw I'm new here so hello everyone! I hope this forum is better than the others that I joined.

Share this post


Link to post
Share on other sites


Hello and welcome !!

Is this bike full time 4WD?

Stock 23" tires?

Make sure the valves are adjusted in spec, nice clean carb & filter, clear muffler ...

I was thinking more of 45 - low 50s ...

Share this post


Link to post
Share on other sites
Hello and welcome !!

Is this bike full time 4WD?

Stock 23" tires?

Make sure the valves are adjusted in spec, nice clean carb & filter, clear muffler ...

I was thinking more of 45 - low 50s ...

What all should I have done? Diff fluid changed, valves adjusted, timing checked, Carb clean?

Share this post


Link to post
Share on other sites

i have heard guys say they will do 5?, but i think alot of conditions need to apply.

the bike is near 500lbs wet, add a 150 - 180lb rider, thats alot for a 350 to push fast especially in 4X4 ... not saying its not true ... if you want up to top speeds, check the compression, make sure valve are in sync, and carb is good and clear ...

i would say a step up in carb jets, a k&n filter or equivalent, and a aftermarket muffler would have you in high 50s ... i know the 350 motor is the same as the big bear except for the top end, i might be scared going over 50 on the bear, i havent clocked it yet, but i would say it goes maybe 40 - 45 ...

there is a governor on the throttle too, you can fiddle with that to see if the speed increases ...

Share this post


Link to post
Share on other sites


if the bike runs good as it sits now, i would dump seafoam every other or so tank to keep the carb clear ... yes, check/change your fluids for sure, timing and valves, a quick compression check can tell you if rings are worn or wearing ,,,

Share this post


Link to post
Share on other sites

A stock "03" Wolverine might do 55mph down hill. I put a jet kit, pipe and K & N filter and barely got there. Mine was a "2002", but not much difference.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By HeWasRidinDirty
      I got this 400, that wouldn't start. It would try, but wouldn't catch. I checked the valves and the L intake was tight at .002. The compression came in around 120. It didn't improve after a couple of drops of oil into the cylinder. So,I figured it was the valve causing the problem. So, I got the valves squared away, but it still won't start. I checked the spark and it seems like it's getting an intermittent spark. It fires a few times then nothing. If l let up on the button and then hit again immediately, it will fire a few more times, then repeat. So, what am I looking at as a possibility? Electrical issues are not my strong point. LOL
    • By Dimelol
      I have a 2003 Kodiak 450 that i purchased a while back with around 300 hours on it. It has never ran right from the beginning. Initially i thought it was just a carburetor issue because it was all clogged up from sitting for months. It has been cleaned, rebuilt, and taken off probably about 10 times troubleshooting this problem. I have quadruple checked everything including float height ect and it is set correctly, the jets are also brand new, needle and seat have been pressure tested as well. So after all of that I am convinced that the carburetor is not the culprit. I have an issue where the idle is very choppy, almost as if it is misfiring with a rich condition on top of that. I can use a brand new plug and run the machine for just a few minutes and it will be a dry and and coated in black carbon build up. The exhaust also has a strong smell at idle. I had trouble restarting it when hot for a while, but i adjusted the valves and it seemed to solve that issue. They were both way out of tolerance (tight). The weird thing is, outside of idle it seems to run pretty well. 
      So with all that being said I have ruled out the carb/valves/compression and moved on to the ignition and this is where i have a few questions about factory specifications. I guess the main question I have is, how strict are these tolerances? And could them being off by this amount cause the issue I am having? Do all three of these parts really need to be replaced? I would like to know before I spend the money on these new parts, and it not fix my problem. Below I will list what the specs were in the service manual along with the reading i got.  This is my first experience testing ignition components. I just found it odd that all 3 are out of spec according to the service manual.
      Spark plug cap resistance: 10 kΩ at 20 °C (68 °F)
      My Reading: 8.90 kΩ
      Primary coil resistance: 0.18 ~ 0.28 Ω at 20 °C (68 °F)
      My Reading: Fluctuated between 0.4 - 0.5 Ω
      Secondary coil resistance: 6.32 ~ 9.48 kΩ at 20 °C (68 °F)
      Reading was within the specified range.
      Pickup coil resistance: 459 ~ 561 Ω at 20 °C (68 °F)
      Reading was within specified range.
      Rotor rotation direction sensing coil resistance: 0.085 ~ 0.105 Ω at 20 °C (68 °F) 
      My reading was 0.3 Ω
    • By Ryan Geiler
      New to the ATV world, picked up a solid used Kodiak 400.  It appears the former owner did some sort of modification for a saddle bag or something along those lines--and I'd like to match it up and replace it.  Not a big deal by any means but something I thought I would give a shot at finding.
      does anyone recognize what kind of luggage/bag/cargo would go where those white tabs are he drilled through that fuel fender?
       
      Thanks again

    • By Romain Catinaud
      Salut! J'ai acheté un quad 450 wolverine de 2006 mais je ne trouve pas le circuit coupé au guidon n'existe pas sur 2006? Merci les gars
    • By amelia slabbert
      Hi I have a YAMAHA RAPTOR 660R 2003
      I have taken of my Air filter and sprayed in my air inlet some carberator cleaner while starting it. That causes some problems. It struggles to start now. Please look at my attachedment video. 
      What can I do now.? 
      MOV_1402.mp4 MOV_1401.mp4
  • Similar Tagged Content

    • By Chayse Hill
      I have a 2003 LTZ 400 that i bought a few days ago. The quad was running fine until last night. I let my brother ride it down the street and back and i didnt notice anything etong with bike. Then my neighbors friend came over and said "can i ride it?" I said "sure" so he ripped it down the road all fine and when he got back it died right in front of us. My brother said it was dieing on him also. He also said that he wasnt using the clutch to shift. I told him he was an idiot. Im throwing that in there incase that caused a problem as well. But today i go to check it to make sure its getting fuel which it is and replaced the spark plug incase it wasnt getting spark but it is. So i started it and it was having a problem starting then i got started and was reving at idle high. So i took it around the block and it died on me a little bit down, so i try to restart it and it started so i kicked it into 1st and it kinda launched on me and started going with the clutch all the way in. Then it died right after and wasnt running right during that process and was idleing all over the place and just died and now i cant get it started it again. Before it would start without the choke or priming it. It would start real quick now i cant figure if it needs to be rejetted or something else. Air filter looks clean also. But any help would be gratelly appreciated!
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By crazynordlander
      Hi All,
      I live in Minnesota and bought a 2016 CFORCE 500 HO. I am in hope to see if there is anyone in the US that is experiencing this sudden drop off in RPM below 4000 RPM. I have uploaded some videos of my issue on YouTube. I will list three of the four I posted. The fourth can be found on my channel but it is a comparison between my Polaris 570 and my CFORCE 500.
      I quit on my first dealer because we just did not mix well together. I brought it to another CFMOTO dealer that just became a CFMOTO dealer in January 2016. They are in a large ranch and agriculture area in a neighboring state that is pretty close to where I live. They have close to every brand available. They are a much larger dealer than the first one I bought the unit from.
      I brought the unit three weeks ago to them and they have worked on it a good solid week and have given up on it. I have read reports from owners in Canada that the dealers there were aware of the issue and have had success in fixing the herky jerky drivability issue.
      I am picking it up tomorrow and bringing it back home. It has been to the trails of the Black Hills this year and was new in late April. 300 miles on it. It has never changed. Very hard to ride on the trails or when I herd livestock.
      Here are the links to my videos.



      I can't accept that this is normal operation. Does anyone from CFMOTO China scan these posts?
      I need help that CFMOTO USA has not provided.
      Thanks
      Kevin
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...