Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

dctaz37

2005 Yamaha Kodiak - No Power In Reverse

Recommended Posts

When I back up with a load on the atv makes a sort of muffled backfiring noise and does not seem to have very much power. Any ideas?

Share this post


Link to post
Share on other sites


Do you have a picture? From what I have read there is no switch and you need to ground a green and white wire out of the CDI. The side effect is no reverse light.

Edited by dctaz37

Share this post


Link to post
Share on other sites

Well now, after looking in the manual, yours and the grizzly 450 dont come with an override button .... why i dont know. My apologies ...

i dont know if there is anything you can do to it stock to eliminate your condition, however, there is a simple mod you can do ... 02 - 03 Reverse OR

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By cliffyh
      Hi,
      Have a 2005 grizzly 660. Just recently started backfiring and showing incorrect speed. Lifted seat and messed with wire going to starter relay, it stops for a bit but seems to come back.
      I ended up pulling all the pins out of the connector for the relay and added new pin/connectors for all 4 wires. fixed it for a little bit but came back shortly after. This was a new starter relay i installed a few months ago. Anyone know if a bad starter relay would do this? 
    • By Michael France
      I have a Kawasaki Bayou 220 KLF220A and I cannot get it to start using the starter button. I have replaced the starter solenoid and the starter relay. I have followed the wiring diagram in the repair manual and it looks like the switch is working well, the neutral and reverse relay have power running through them and appear tp be working correctly. However, I can not find a wire runnng the the starter button that has power on it. Anybody have any idea what the break down is?
    • By Steve Howard
      Ran find shut down the quad next day would start and idle when you try to accelerate it would start popping through the carb got a rebuild kit soaked it in chem clean after break down for 12 hours on slow vibrate reassembled and adjusted per manual still the same thing any help would be really appreciated thanks and happy ridding  
    • By dee004
      Hey all. Anyone have any ideas of fabricating an air snorkel for a 2005 TRX500FM and all venting extensions required as well? Thanks in advance Don
    • By wendi loden
      I replaced the fuel pump filter and it ran great for a week or so. Then while driving across the yard in 3rd gear it shut off and hasn't started since. It has fire and its getting fuel, all fuses are good, battery fully charged. The fuel pump relay seems to be warmer than it should be when spinning it over. Any help is appreciated!
  • Similar Tagged Content

    • By Wali
      I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
      when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out 
       
      Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
      When i try to pull start (push start/roll start) it made a not normal sound  and wouldnt stay running.
      If my bottom end is blow why would it still turn over fine,
      Are my valves siezed or not working properly 
      or is my timing off causeing valves to not open in correct order with fire 
      PLEASE HELP all help is appreciated 
    • By Hunter Aldridge
      Some times I get spark some times not can ride then it just dies and wont get spark it has new cdi box and stator but I don't know if it has the pickup coil I'm at a loss
    • By William Sims
      I have a 400 4by4 ,2005 green model,
      wounding how many different CDI boxes will work on it
       
    • By jerry houston
      Eiger 400 Suzuki runs fine Cook-Out joke face off the handlebars put it back on and will not start now will crank no no spark
    • By colin james
      View File 2012-2014 Polaris Sportsman 400 HD Service Manual
      This the factory service manual for the 2012- 2014 sportsman 400 hd service manual 
      Submitter colin james Submitted 02/08/2019 Category Polaris ATV  
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...