Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

chuey12

2010 Suzuki ltz400 - Problems

Recommended Posts

I have a 2010 Z400 and it will start up an idle fine but when you go to give it gas it just stales out and wont run at high temp. Any ideas?

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Mike Johnson
      Does anyone know what the 3rd item is behind the battery on this ATV ? I know 1 is the,  solenoid1 is the CDI box, what is the 3rd.
    • By Daniel Gibson
      Working on a bayou 220 that has been ran extremely hard it's whole life. Literally had almost an inch thick dirt/oil covering the motor. Yeah that bad. Surprisingly it runs though. I cleaned the carb and tank multiple times. They're clean enough to eat off of. Readjusted valve lash and set timing. Was about 3 teeth off. It cranks good and runs good only problem is I have to cover the carb intake basically choking the hell out of it for it to start. The com choke works fine. It does this each time I start it regardless of temperature both ambient or motor. Wth? Compression is at 115psi I get 130s if I put a little oil in the piston chamber. Please help. Thanks 
    • By JC4x4
      My Honda Fourtrax won't start. The starter is kicking the engine over, but it won't start. It sat for about a year while I was living away, so I thought it might have been bad gas. I completely drained the fuel, flushed the fuel lines and filled it with fresh gas. However, still nothing. It started and ran fine the last time I used it. Any suggestions on how to diagnose this? It could be fuel or electrical at this point. Is there an easy way to rule one or the other out? Thanks
    • By Quadrunner44
      I have an older 1980s Suzuki quadrunner red lt 4wd (250)
      so just finished putting it all back together and was running fine just needed to adjust the rebuilt carb
      bf decides to hook up an air chuck to the gas tank because it got a shot of air in the gas line well 120psi didn’t agree with any of the parts including the new carb 
      end result : new battery new carb now it just clicks (one single click) won’t turn over 
      hard to pull start gets hung up (unless I remove the spark plug ) gas flooded out the first time but now does nothing purchases a new starter waiting the arrival 
      could there be damage to the crank shaft or pistons etc? Or install the new starter and try to fire it up ? What caused the starter to die after he flooded everything with gas was working fine. 
      Thank you 
    • By Flipper Tiffany Roper Jones
      All I have been through everything. Bought brand new.
      Throttle safety switch 
      Cam and rockers
      ECM
      Carborator
      Stator
      Fuel safety switch 
      Battery
      Everything every forum has spoken of I've bought sealed airbox completely tight unplugged black wire on trans. I have literally done everything in the book.Checked oil today full of gas anyone no anything what might b wrong. Next I'm taking head off and making sure valves seat any ideas.
  • Similar Tagged Content

    • By Anthony Marceau
      Hi everyone! I have a 1986 yamaha moto4 200 that's been sitting for a while! Cleaned the carb, replaced engine oil, put fresh gas in it. Got it running and went for a ride! It was running great just a little backfire once in a while! I barely made it home on the way back and now the bike won't run at all since then! It will start if I give a little bit of throttle but dies instantly as soon as I let go off the throttle! And even if I try to rev it up it'll sound like its not getting enough gas.. it revs up a couple hundred rpm's and backfires through the carb.. it almost sounds as if I was trying to take off from zero in 5th gear! Nothing is seized though! I dissasembled the head and the piston and cylinder are fine! Rebuilt the carb, replaced the ignition source coil.. I don't know what to do anymore.. compression test shows 90 psi Specs are 128 psi but i'm not sure if I trust my compression tester.. any ideas? Thanks!!
    • By Cobra_GT
      i am buying a z400 and am wondering what smooth bore carburetor you guys are running for performance on this quad. Flat or round slide and what size. i would like to get that cv carburetor off of there for performance, thanks. peace.
      ct
    • By Cobra_GT
      What’s up fellows I am looking for some heads for z400 motors or the whole motors themselves. Also I am looking for Keihin FCR carburetors in 39mm and or preferably the 41mm is what I would prefer. The newer the better I hate to price a new casting of that head from the dealer. Please hit me back in the thread or pm me if you can help me. I need to build a motor to beat a Banshee. All offers will be considered. Thanks for your attention in the matter. Peace.
    • By Steve1266
      I went out to ride my quad today. When I started it up it ran for a minute, then died. Since then it will turn over but won't start. I've check the spark plug and get great fire. I have had this quad for about 6 months, and very new to breaking it down. But need help. Thanks
    • By Bearman
      Long story short. I bought this off my neighbor and only has 3 gears. The part that holds the shifter rod on broke, this is on the inside where the clutch is. The rod moved out of its spot and when they welded it back together only has 3 gears. I have a new case for it just need to know how to get the shifter in the right spot before I put it back together. I am missing the indicator that shows me where neutral is. A link to a good Manuel would be great. Thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...