Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

oleblue

4wd Problems, relays, switch, testing servo, need a servo motor? Look here

Recommended Posts

I just launched a new site that deals with all and any problems with the 4wd system on Yamahas. I have how to videos for testing the servo, disassembling the servo, replacing and purchasing the servo (motor only), testing relays, and testing the push button switch.

I also have a link to download the 4wd testing portion of the service manual.

Check it out at 501parts.com - Yahama Servo Motors

Let me know if I can help.

Heres a few of the videos and pics

http://www.501parts.com/files/stacks_image_252.png

http://www.501parts.com/files/stacks_image_250.png

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dimelol
      I have a 2003 Kodiak 450 that i purchased a while back with around 300 hours on it. It has never ran right from the beginning. Initially i thought it was just a carburetor issue because it was all clogged up from sitting for months. It has been cleaned, rebuilt, and taken off probably about 10 times troubleshooting this problem. I have quadruple checked everything including float height ect and it is set correctly, the jets are also brand new, needle and seat have been pressure tested as well. So after all of that I am convinced that the carburetor is not the culprit. I have an issue where the idle is very choppy, almost as if it is misfiring with a rich condition on top of that. I can use a brand new plug and run the machine for just a few minutes and it will be a dry and and coated in black carbon build up. The exhaust also has a strong smell at idle. I had trouble restarting it when hot for a while, but i adjusted the valves and it seemed to solve that issue. They were both way out of tolerance (tight). The weird thing is, outside of idle it seems to run pretty well. 
      So with all that being said I have ruled out the carb/valves/compression and moved on to the ignition and this is where i have a few questions about factory specifications. I guess the main question I have is, how strict are these tolerances? And could them being off by this amount cause the issue I am having? Do all three of these parts really need to be replaced? I would like to know before I spend the money on these new parts, and it not fix my problem. Below I will list what the specs were in the service manual along with the reading i got.  This is my first experience testing ignition components. I just found it odd that all 3 are out of spec according to the service manual.
      Spark plug cap resistance: 10 kΩ at 20 °C (68 °F)
      My Reading: 8.90 kΩ
      Primary coil resistance: 0.18 ~ 0.28 Ω at 20 °C (68 °F)
      My Reading: Fluctuated between 0.4 - 0.5 Ω
      Secondary coil resistance: 6.32 ~ 9.48 kΩ at 20 °C (68 °F)
      Reading was within the specified range.
      Pickup coil resistance: 459 ~ 561 Ω at 20 °C (68 °F)
      Reading was within specified range.
      Rotor rotation direction sensing coil resistance: 0.085 ~ 0.105 Ω at 20 °C (68 °F) 
      My reading was 0.3 Ω
    • By Ryann Racho
      So Id say about 2 years back I bought a 2013 Polaris Sportsman 500 H.O. off of my uncle. It ran perfectly, nothing wrong at all. I usually go mudding with it or just ride trails with buddies. So as you would assume, the quad is quite dirty from sitting for a few weeks.
       
      STUTTERING PROBLEM: I noticed one day out of nowhere that in high gear at 15-20 MPH, I was already maxed out at 4500-5000 RPM  It would get to 15-20 mph, max out on rpms and start sputtering. It sounded like it was basically acting like it couldn’t go any faster than this.
       
      IDLING PROBLEM: I was fucking with the carberator the other day maybe thinking that is causing my sputtering, and now my idle will shoot up to 2600 on start usually, then I will turn the throttle adjustment down to the normal 1400. The rpms with then fluctuate 10-30 rpms back and forth repeatedly, it will then run for about another 30-60 seconds and the RPMs will slowly drop to about 900-1000 RPM and stall out. I replaced the carburetor and everything seems to be working perfect on that, no leaks and what not but it’s still acting strange. Also, I’ve noticed that when looking into the Electronic Throttle Control that two plates that aren’t supposed to touch have to be WAY past touching to even try to fire up. Even when set at a wide open throttle like that, I still have to give it some throttle to get it to fire up.
       
      Here is what I have done so far: 
      Checked the belt and clutch
      Changed out spark plug (Last one was covered in carbon)
      Cleaned the intake and air box
      Replaced the carburetor
      Replaced the inline fuel filter
      Checked that all lines on carburetor are connected into the right spots
      Checked If intake boot was cracked (Not from what I can see)
      Unhooked and reattached new carburetor (About 4-5 times)
      Cleaned battery terminals and battery off
      Shut on and off Gas Line Cutoff Valve
       
       
       
      My next thoughts are that maybe the TPS is fucked up or maybe the Spark Arrestor is plugged with mud. I was thinking tomorrow to purge the exhaust and also check the ohms output on the TPS.
       
      ANY HELP IS GREATLY APPRECIATED. I HAVE BEEN BATTLING THIS FOR WEEK AND REALLY WANT TO GO RIDING. THANK YOU!
    • By Andrew Serrano
      I have a 2000 Suzuki LTF -300 King Quad. My problem is it will start up great, very fast. It will run fine until it gets hot and I turn it off.  If I let it sit for a bit it will not start until I hold the throttle wide open and crank on the starter for quite some timr, acting has if flooded.....but I checked the spark plug one time this happened, went to change thinking it was flooded but only found a dry Plug????  It starts like if flooded but plug was dry, it takes awhile to start, then to get going I have to really rev it to get it clear and going...Thanks any suggestions would be great, thanks everybody in advance...!!!
    • By aaron cesene
      I have a 08 artic cat 366 4x4 fis red.   Blown motor.  Anyone know or where to find out what engines are compatible with this bike?  Would love to upgrade if possible.  My other option is to rebuild.  It broke good might have pieces in jug!!  So might have to come all the way apart.   Help please
    • By utvboard
      Introducing the Dash Frame system for the Kawasaki Teryx from Black Rhino Performance. The Dash Frame fits nicely into the middle of your dash, and is designed to closely follow the shape of the Kawasaki Teryx dash. This frame puts your gauges and switches at the same angle as the upper dash for easy viewing of the gauges and convenient placement of switches. The panel provides mounting for 3 2"
      https://www.utvguide.net/dash-frame-system-for-the-kawasaki-teryx-now-available/
  • Similar Tagged Content

    • By BigRuss
      I have a Kawasaki  bayou 4WD that started squealing when giving it the gas from a stop. It almost sounds like a fan belt but the dealer replaced the belt about 30 hours ago, so I don't think it is that. As best as I can tell, it actually sounds like it is coming from the front end. Once I am running and moving at a speed, I don't hear the squealing anymore. My first thought was to put fan belt dressing on the fan belt, as a quick test for the problem. It makes the noise when hot or cold.
      Another problem, that started before the dealer changed the fan belt, is that you give the quad a little gas, and nothing, give it more, and nothing, give it more, and it lurches and takes off. The dealer said it needs a new clutch, which I don't buy. less than 400 hours and it needs a clutch? I would say it needs an adjustment. When the quad is cold, as in I just started it for the first time in hours, it does not lurch. It is just fine. It lurches only when it gets hot, as in when you can hear the fan once in a while to cool the oil.
      Any help or insights would be great.
       
      Russ
    • By Kingquad1
      Hello I am new hear. I just purchased a 1998 Big Bear. It was sitting for 3yrs in storage. The guy I bought it from got the carb cleaned and it runs good. I am having problems with the neutral light. When I shift into neutral the light does not come on. If I mess with the gear shifter, I can get it to come on so I can start it. I can still pull the hand brake and start it that way. I cant find the neutral safity switch on this machine. Any suggestions would be great.
    • By atvinca
      I just picked up a really clean 1995 Moto 4 350. It runs great, but it will only go into one forward gear, neutral and reverse. I can run the shifter up and down and it will finally find a gear, or neutral. What should I do to trouble shoot this?
      Does anyone have a service/repair manual for this model?
      Thanks!
    • By lulu
      neutral light does not come on when in neutral, engine will not turn over. have not found any bare wires or loose connections. not sure exactly where the neutral switch is located or how to replace it. battery is hot and reverse light works
    • By stepadery
      The connector that that plugs into the switch evidently was caught by something while riding (I'm guessing) and a couple of wires were pulled out of the connector. I have attached a picture. Is there any where that I can get this female end with pigtails without buying the entire wiring harness? I'm a pretty good wire splicer and solderer.


  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...