Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Scott Matthews
Just picked up a 1989 Big Bear 350 for $250 CAD. Bike was running but lost crank and spark. They've installed a new coil, a couple relays, and installed a Ford starter solenoid in place of the original. Now it cranks but has no spark so they sold it to me. Does anyone have a wiring diagram for this bike so I can test some wiring. Also any ideas as to direction to head would be nice. Lots of things have been hacked together so I know it probably wont be to easy. The ignition switch was replaced with a toggle switch, I already mentioned the Ford solenoid which 1 of the small wires was not re-installed, and a diode or something was removed from the oil temp sensor wire. I'm sure I will find more so a diagram would be amazing.
Working on my oldest son's buddy's 2000 Big Bear. He was having some power loss at WOT so i thought it worth while to clean the carb and put at kit in it...or at least clean the OEM jets and use the new orings that come in the kit. It starts and idles like a champ, but dies and wants to backfire with any throttle at all. I assume lean because it will run decent with the choke on. Air screw adjusted fine, nice crisp idle. This one has fuel/air screw, low speed jet, mid jet, and main jet. I was assuming just trash in the low speed circuit so pulled it and cleaned again, still does the same.
Two questions I guess:
1. Does it sound most likely trash in the off idle circuit? This one has a few more passages and jets than I'm used to...and a darn diaphragm.
2. It now really wants to leak at the bowl drain screw. It doesn't seem to tighten enough to completely stop the flow. Seat looks good, screw was dirty but cleaned up fine with a touch of 2000 grit paper. First for me. Any idea here?
By Stacy Hanks
I have 2000 Yamaha bear tracker 250 - igniton relay and starter relay both were replaced also the neutral switch indicator was replaced-- bike will not show light on for neutral or start when button is pushed
Similar Tagged Content
these are what i have in my collection ... always looking for more
Linhai 250 - 360 Service Manual
Linhai 260 - 300 Parts Manual
Linhai 260 - 300 Service Manual
Linhai 300 Parts Manual
Linhai 260 Service Manual
Linhai Bighorn CUV Service Manual
By Zacharia Maisonneuve
i have a 1993 timberwolf yamaha and the compression is good and lights work but for some reason the electricity is not going to the spark plug(s)! i got a friend to check it out and they said its no use but im not giving up! please help with this!
By Connor Tuftin
I have a 1988 300 Honda FourTrax, All wheel drive.
My brother and I were fixing up this quad. We put a brand new battery and fuses in and it was running fine until we put the quad into reverse. As soon as it was put into reverse all of the electrical cut out and power wasn't making it to the head unit anymore and both of the brand new fuses popped. We figured there might have been a short from the starter or solenoids, but they are all working properly. At this point we don't know where to start looking for where the short could be. I'm just wondering if anybody has had the same issue or knows of similar issues that could cause these electrical shorts?
By Resurgence Small Engine Inc.
Not satisfied with the commercially available versions, Jonathan recently built an ATV spring compressor.
In this video, he demonstrates using it to remove & re-install the spring on an ATV coil-over shock absorber.
Mistake in video - the coil-over shock is not quite a McPherson strut.
If you are inspired to build your own spring compressor, feel welcome to use any ideas from this video.
Thanks for watching! Resurgence Small Engine Inc.
Recently Browsing 0 members
No registered users viewing this page.