Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
Recently I noticed gas leaking from under the gas tank on my 2005 250 2x4. As I looked closer it appears to be leaking from the shut off valve under the tank. It's the valve with the handle that can be turned to open, close or reserve. Can this part be replaced? Thank you.
Hi guys I'm in the market for a new ATV. I narrowed my choices down to King quad 750 Grizzly 700 and Rubicon 520, I own a 2006 500 Rubicon right now and I like the reliability and power for plowing. However it is not a capable ATV. When quading with other guys it falls short with ride quality and ground clearance. I also have a 500 King Quad 2015 which I like and will keep it for my wife. It is very strong and reliable also. However my plan is to sell my Honda Rubicon and replace it with a 2020 of one of the these mentioned above. Can anyone give me their take on one or all of these machines and why you picked what you picked?
Similar Tagged Content
Ok...I'm gettin' me juevos ready to do an oir filter clean....
Went to my local harley/quad dealer and he had me purchase the No-Toil kit (Cleaner, Air Filter Oil, Rim Grease)
What I've read is that the No-Toil cleaner will NOT clean
other oils off air filters....just the No-Toil oil....
So, I've also read that others have cleaned their air filters
in the kitchen sink, used gasoline, or used flash solvent....
Looking for advice as I've mentioned I'm very mechanically
I'm going to wash the air box seal in the sink and give it a good dry....
One more thing......No-Toil or Bel-Ray for filter oil?
I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
Has anyone found engine oil in their air filter box. The must be little or no baffle between crankcase ventilation and that hose that attaches to the air filter box.
I went to pick up my ATV today 60 miles away that they could not fix the jerky low speeds on and before I loaded it decided to check on this. Sure enough there was a good coating of oil with some pooling in the bottom of the air filter box. The air filter has oil on it too but is it a dry element or oiled element type. My guess from the color of it dry.
I heard on a comment on my YT videos that there is a kit for this issue? Is this a CFMOTO fix?
I'm going into my '11 Grizz 700 to adjust valve clearance for the first time and when I button everything back up I'll be replacing all the gaskets / o-rings. The 5 I'll be replacing include (from the top down) both valve cover gaskets, cylinder head cover gasket, and the 2 gaskets in the crankcase cover.
Do I need to coat these gaskets with motor oil before putting them on like when replacing your oil filter?
Recently Browsing 0 members
No registered users viewing this page.