Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

jtbaker1989

2006 Yamaha Bruin 350 - Running Issues

Recommended Posts

Hey everyone. I have been poking around this site for awhile and I am in need of yalls assistance. I have a 06 350 bruin. It has sat in my parents garage for about 2 years and was never started. I got it home, put fresh fuel and plug in it. It would start and run great but it wouldn't idle unless choke was on. Also when you were moving and let off the throttle it would make a pop noise down by the carb area. I thought it was a dirty carb so I sprayed some carb cleaner in it and didn't help.

I removed the carb, tore it down and cleaned it. I removed the jets spraying carb cleaner and compressed air thru them. I removed the float as well and cleaned. I drilled out the plug that covers the air/fuel mixture screw. I read where the spec is two turns from fully seated. So that is where I set it at. Before I did that, I removed the screw and spring and cleaned that bore out as well.

I reassembled and now I have issues. It is very hard to start, choke or no choke, and when you do get it started, you have to hold the throttle at 3/4 way to keep it running. It will run very rough at 3/4 as well. With the air filter off, while trying to start, it is blowing a lot of fuel back out into the air filter and the plug is getting fuel fouled very bad. I removed the carb again thinking I messed something up or got the float stuck but everything looked fine. I put the carb back on the second time and it didn't change a thing. I assume its something I did since its not running like it did before I tore down the carb. Can anyone please help? Thanks a lot.

Share this post


Link to post
Share on other sites


check your valve clearances ... that would make it hard to start and push fuel back thru the carb ...

I was thinking about checking that but I figured if its running worse after I cleaned the carb, then I thought it was something I did. Also, with the plug removed if I hit the starter it will blow my finger off the hole.

Share this post


Link to post
Share on other sites

i cleaned the carb on a 91 big bear 12 or more times before i got it right LOL ... i was told to adjust the valves every 2 years, i believe that also ... just a suggestion ...

Share this post


Link to post
Share on other sites


Almost certainly valve lash and/or burnt valve(s). My friend has one. His was doing the same thing. Adjusted the valves, found the intake valve lash at 0mm (held a bit open). Additionally, rocker not flush to the top of the valve (gap larger on one side than the other). After the valve adjustment it runs a lot better but is still lean (runs better with a bit of choke) and small pops (backfires) when backing off after high rpm. Also took the carb off. All jets clean, carb in good shape, not dirty...no issues there. It now easily runs good enough to ride...but still not quite right. I am 95+pct sure the remaining issue is slightly burnt valve as the valve-to-rocker-not-flush issue, popping, and lean condition are classic indicators of this.

They are notoriously under-powered (heavy to start with). Folks ride them and you get high rpm for extended periods. Over time this results in burnt valves (especially when the high school kids are riding the crap out of it for years).

Share this post


Link to post
Share on other sites

I am having almost the same problems and I recently adjusted my valves and it ran great except for at full throttle. So, I pulled the carb and found some debris in the main jet. Put it back together and now I can't get it to run. If I pull the diaphragm with the needle it runs.

It's running really rich and I can't figure out why. I've pulled the carb and checked it at least 5 times and can't figure this one out. Any help would be greatly appreciated.

Sent from my SM-N920P using Tapatalk

Share this post


Link to post
Share on other sites

Turns out when I cleaned my carb last time the main jet nozzle fell out. My kid found it on the floor in the garage. I'll update after work when I put it back in.

Sent from my SM-N920P using Tapatalk

Share this post


Link to post
Share on other sites


any one know if 95 kodiak 400 has a air adjustment screw on the carb? i know where the throttle adjuster is and where i think the fuel is but no air screw...can anyone help?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tiffany Rowland
      I recently purchased an 07 Honda sportrax and when I was checking the spark plug I saw the boot was ripped nearly in half. When I removed the plug it was blackened and covered in oil. How can I thoroughly clean the plug hole and remove any debris that is in there? Is there a small tube like vacuum or something of the sort made for stuff like this? The machine my dentist has would be perfect, maybe they do rentals! 😁
    • By Tiffany Rowland
      I am working on a Honda sportrax I just got my daughter for get birthday and the reverse and neutral light are not working. When I traced the wire down I saw that it wasn't plugged in but I don't see where it is supposed to connect. Does any one have a general idea of where I should look?

    • By Tiffany Rowland
      I recently purchased an 07 Honda sportrax and when I was checking the spark plug I saw the boot was ripped nearly in half. When I removed the plug it was blackened and covered in oil. How can I thoroughly clean the plug hole and remove any debris that is in there? Is there a small tube like vacuum or something of the sort made for stuff like this? The machine my dentist has would be perfect, maybe they do rentals! 😁

    • By orvilleortiz538
      So My 07 Kymco Mongoose 300 was having a bit of choke issue and I have an Ultrasonic and decided to dip it in for a good clean up,and now the atv don’t want to start,it tried but it backfired a little bit but still won’t start,any suggestions?
       
       
      Sent from my iPhone using Tapatalk
    • By Frank Angerano
      Take a look at this.  Curious about everyone’s input.it looks pretty good.   We all have this common problem of accessing the air fuel mixture screws.    
      The reviews look pretty good.  I may order one just to see how it works out.
       
      https://www.motosport.com/rd-flex-jet-fuel-mixture-screw
      They also have other types that will work on this site.  
  • Similar Tagged Content

    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By Kyboy
      Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
    • By davidwestfall
      looking for direct shift shifting lever that properly fits my 2003 Yamaha warrior 350 and fits my foot the same as a stock 2003 Yamaha warrior 350 shifting lever fits my foot
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...