Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

I am a new member and was hoping i could get some good info on why my 2002 yamaha blaster atv will not run. the ignition light will not stay on when i try to start it. i put new plugs, cleaned gas. when i pulled it with my pick up with someone on it , it would start and run, now it will not even start by pulling it now. any one out there with some good advice? :aargh:

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Danielle Bingham
      So I have my very first Atc still. My dad gave it to me when I was very little (was brand new; one owner bike), and it has needed just two repairs over the approximately three decades: replace/repair pull-start. 
      Any ideas of some simple & not so simple mods/upgrades for this classic? I'd LOVE to swap the tranny for one with a real clutch, personally...possible??
       
    • By Asen_77
      Hi All,
      My name is Asen and I am from Eastern Europe, Bulgaria. Riding a Yamaha Raptor 700R and this is my first Quad wanted for a vey long time :)

       
    • By Dimelol
      I have a 2003 Kodiak 450 that i purchased a while back with around 300 hours on it. It has never ran right from the beginning. Initially i thought it was just a carburetor issue because it was all clogged up from sitting for months. It has been cleaned, rebuilt, and taken off probably about 10 times troubleshooting this problem. I have quadruple checked everything including float height ect and it is set correctly, the jets are also brand new, needle and seat have been pressure tested as well. So after all of that I am convinced that the carburetor is not the culprit. I have an issue where the idle is very choppy, almost as if it is misfiring with a rich condition on top of that. I can use a brand new plug and run the machine for just a few minutes and it will be a dry and and coated in black carbon build up. The exhaust also has a strong smell at idle. I had trouble restarting it when hot for a while, but i adjusted the valves and it seemed to solve that issue. They were both way out of tolerance (tight). The weird thing is, outside of idle it seems to run pretty well. 
      So with all that being said I have ruled out the carb/valves/compression and moved on to the ignition and this is where i have a few questions about factory specifications. I guess the main question I have is, how strict are these tolerances? And could them being off by this amount cause the issue I am having? Do all three of these parts really need to be replaced? I would like to know before I spend the money on these new parts, and it not fix my problem. Below I will list what the specs were in the service manual along with the reading i got.  This is my first experience testing ignition components. I just found it odd that all 3 are out of spec according to the service manual.
      Spark plug cap resistance: 10 kΩ at 20 °C (68 °F)
      My Reading: 8.90 kΩ
      Primary coil resistance: 0.18 ~ 0.28 Ω at 20 °C (68 °F)
      My Reading: Fluctuated between 0.4 - 0.5 Ω
      Secondary coil resistance: 6.32 ~ 9.48 kΩ at 20 °C (68 °F)
      Reading was within the specified range.
      Pickup coil resistance: 459 ~ 561 Ω at 20 °C (68 °F)
      Reading was within specified range.
      Rotor rotation direction sensing coil resistance: 0.085 ~ 0.105 Ω at 20 °C (68 °F) 
      My reading was 0.3 Ω
    • By Rich1028
      New Member from Saginaw,MI.

      I have A 1991 Honda 250X bought it new,still kinda good shape,want to get back to ridding some trails with it.
      have not been on the trails since 1995.
      used to ride from Houton Lake to St. Helen get gas and food and turn around,made for a great days ride.


      looking to read lots in this forum.

    • By gouletp
      The thing sat since Christmas 2018 and while I decided whether to replace the starter (which I finally did today).  I am not sure if I added fuel stabilizer or not but chances are good I did.  I kept the one year-old battery well charged during the winter.  It turns over well but won't start.  I have a blue spark on a brand new plug.  When I pour a bit of fuel down the cylinder, the engine starts and runs for a few seconds (once for as long as about 8 sections) and then dies.  Even before adding fuel to the cylinder I noticed that the spark plug was wet with fuel.
      The air filter looks a bit dirty so I removed it just to see if the engine would start better but it made no difference.
      If the fuel did not contain stabilizer then the carb may be gummed up.  I don't really want to remove the carb to do a thorough cleaning.  Is there a product I can spray into the carb while the engine turns over that will clean the carb?
      Any other suggestions?
      Thank you
  • Similar Tagged Content

    • By Kristpj
      I know this tooic has been addressed by many, I’ve looked through many forums and pages. I did not find anything like the problem i have.
      I have a 2007 Kingquad 450. I have a new fully charged battery. When i turn the key, the dash flashes and seems to struggle before getting fully lite. We can hear a small relay near the computer clicking, i think it is the fuel pump relay. When i turn off the engine kill switch and press the starting button relays click and all the power shuts off, i turn the key off, engine kill switch then start over, power is there. Atv will start with pull start, but not elextricly. if i try to use my winch, all power cuts and engine dies. 
       
      Can anyone tell me what it may be? or has anyone fsced an issue like this before?
    • By Paul Maple
      I have a 1999 Sportsman  500, it was running fine, than started to lose power in the winter, I adjusted the idle screw and away I went, than a few weeks ago it died, I have found that i am flooding the engine, compression was at 70PSI and due to the compression release mech. i assume i am good as it compared to the same PSI on a 2000 sportsman 500 i have. i cannot start the atv unless i go full throttle and it starts an runs for about 30 sec than dies, again it is flooded. i ordered a new carb off ebay as i could get one for around $40. put that in same issue, i have checked the timing, (good), valves out of adjustment i adjusted to .006 still same issue, i have found the exhaust lobe and rocker arm to have some wear, i have ordered new ones, but am looking for any other input in this area as well. would the exhaust cam and rocker arm cause the engine to flood? i have used a bore scope and the piston liner has good cross hatching still? any input would be great.
    • By scotty2hotty01
      i have a older honda 350 cc quad that seems to start and other days will not.spark seems to be gone and there when it does run.I checked newer coil odd a older yet Honda but no help and idea I going to find the serial number as forget the year but believe around 1995 to 1997 year besides that great quad but cant run it so great this way  and need it for chores around the acreage. Any help would be great. Ive check all fuses as well as the fusable ling which was fine until I screwed with it now need to buy another as have it wired not so safe.I handy but now have copd which takes away the brain power some.Any help would sure be appreciated 
    • By Russs
      I have a 2006 Polaris 500 sports man and having trouble starting it and keeping it running.  
    • By Michael Taralli
      My 2006 Prairre will only start with a shot of starting fluid. Any ideas or suggestions of what might be the problem?? Thanks.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...