Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Kevinjrr

'97 TRX300FW Front Brake Issue

Recommended Posts

I have completely replaced my front brake shoes, hoses, and master cylinder. I have bled the brakes the best I could. I am still unable to build up much pressure. The wheel cylinders only push out about 1/8" when the handle is squeezed.

What should be the typical travel on the cylinder for the brake shoe to hit the drum?

I've used a brake bleeder, but still can't get all of the air out.

I'm not sure what else to do.

Any thoughts?

Share this post


Link to post
Share on other sites


i had to adjust the star wheel so the shoes were almost touching the drum before i got them right. the air is probably out already, but like you said, not enough travel from the wheel cylinders ...

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Mo Salem
      So my front hub broke, I’d like to put aftermarket on. Hard to find new oe ones. Please help. I’m new to all of this, I have some car knowledge and try to apply it
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By raybob
      replacing carb,, the bigger line on right side top of carb does it just vent to the air,, cant find where to hook it up to also I want to check the oil and gear oil I checked the oil in motor and the rear end my question is looks like allen plug on left side of motor if you are setting on the 4 wheller, ps it hs a oli leak any help would be great. Ray in kentucky
    • By Todd Barrett
      Hi all 
      I'm finding it rather difficult to find 10"x6" front rims. My question is will 12"x7" fit and will there be enough clarence when on full lock? 
    • By derick geisendorfer
      I found a black rubber hose hanging down from the front of my Sportsman 850.  I'm trying to see if it's the diff vent hose, or something else and if it's something else, what it's supposed to attach to...  
  • Similar Tagged Content

    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By crazynordlander
      Hi All,
      I live in Minnesota and bought a 2016 CFORCE 500 HO. I am in hope to see if there is anyone in the US that is experiencing this sudden drop off in RPM below 4000 RPM. I have uploaded some videos of my issue on YouTube. I will list three of the four I posted. The fourth can be found on my channel but it is a comparison between my Polaris 570 and my CFORCE 500.
      I quit on my first dealer because we just did not mix well together. I brought it to another CFMOTO dealer that just became a CFMOTO dealer in January 2016. They are in a large ranch and agriculture area in a neighboring state that is pretty close to where I live. They have close to every brand available. They are a much larger dealer than the first one I bought the unit from.
      I brought the unit three weeks ago to them and they have worked on it a good solid week and have given up on it. I have read reports from owners in Canada that the dealers there were aware of the issue and have had success in fixing the herky jerky drivability issue.
      I am picking it up tomorrow and bringing it back home. It has been to the trails of the Black Hills this year and was new in late April. 300 miles on it. It has never changed. Very hard to ride on the trails or when I herd livestock.
      Here are the links to my videos.



      I can't accept that this is normal operation. Does anyone from CFMOTO China scan these posts?
      I need help that CFMOTO USA has not provided.
      Thanks
      Kevin
    • By atvfarm
      Ok Im new here. I was given a cougar 250 and i put a new carb on it and it will idle great but anything above low rpms spits and sputters. also is this thing suppose to have a fuel pump or just gravity feed from petcock?
    • By atvfarm
      Ok Im new here. I was given a cougar 250 and i put a new carb on it and it will idle great but anything above low rpms spits and sputters. also is this thing suppose to have a fuel pump or just gravity feed from petcock?
    • By biggreen2010
      ok it will start up an run but quits a lot till it gets warm, but has a bad miss an wont idle, I have a brand new Honda carb on it, good gas flow, new plug, but when I let the throttle go below a quarter, it backfires through carb an tail pipe:confused: so it has never had any electrical work or mechanical work done...it just started all the sudden, I'm think it may have ignition coil breaking down, or cdi box going bad...anyone had this trouble before? let me know what you did to fix it. thanks:skeptic:
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...