Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Mike8623

1996 king quad CDI unit????

Recommended Posts

OK guys, Ive got a 1996 suzuki king quad 300. Just where and how do you get to the CDI unit on these? Is there a way to check these if you dont have the suzuki tool or meter?

Share this post


Link to post
Share on other sites


OK guys, Ive got a 1996 suzuki king quad 300. Just where and how do you get to the CDI unit on these? Is there a way to check these if you dont have the suzuki tool or meter?

Well this is a long term problem that keeps getting slowly worse. The atv runs fine for awhile and then especially when it starts getting cold it begins not wanting to start. It also wants to not want to start when i go on long rides.

I took it to a suzuki dealer in helena last year and they replaced the piston and honed the head and it ran fine for awhile but then it started right back into not wanting to start, especially in cold weather. I got out the book and started through the not wanting to start section. the gas is fine, the breather tube is fine but there appears to be a weak spark at the plug. so I am just following the book. It said to check the CDI and Ignition coil but the manual really doesnt show a good picture of exactly where they are.

Share this post


Link to post
Share on other sites
On 9/22/2014 at 10:17 AM, Mike8623 said:

Well this is a long term problem that keeps getting slowly worse. The atv runs fine for awhile and then especially when it starts getting cold it begins not wanting to start. It also wants to not want to start when i go on long rides.

I took it to a suzuki dealer in helena last year and they replaced the piston and honed the head and it ran fine for awhile but then it started right back into not wanting to start, especially in cold weather. I got out the book and started through the not wanting to start section. the gas is fine, the breather tube is fine but there appears to be a weak spark at the plug. so I am just following the book. It said to check the CDI and Ignition coil but the manual really doesnt show a good picture of exactly where they are.

Hey Mike, I have a similar problem. What was the final cause and solution to the weak spark/no run situation?

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By wwdubose
      I have two 2003 Suzuki Ozark 250s, both 2-wheel drive.  Last time we rode them about a year ago, the red one was not running well, didn't want to idle, backfired a lot.  The green one ran fine. 
      Fast forward...I ordered a carb kit for both of them, thinking the red one has some trash in a jet.  Both of these ATVs have had little use and I've always ran the gas out after use (put an inline cutoff valve in gas line).  I pull started the red one to verify it was still running bad.  It will start and idle, but as soon as you give it any throttle, it dies instantly.  Give it a little choke, dies instantly.  Took the carb apart and it was spotless.  Went ahead and cleaned all the holes with carb cleaner and blew everything out with compressed air.  All new jets, main jet holder, and needles.  Put it back on and nothing changed.  Starts, idles (not for a long time), but dies as soon as you give it gas.  Same happens when you put the choke on.  It does the same thing when I try to run it turned to prime on the petcock as it does in the on position.
      Not an air filter issue.  It is clean and it does the same exact thing with no filter on it.
      Thought maybe there was a float issue or maybe a damaged diaphragm, so I took the carb off the green Ozark and put it on red.  Started up and initially ran normal and revved for about 10 seconds and then started doing the same exact thing.  Starts, idles (not for a long time), but dies as soon as you give it gas.  Same happens when you put the choke on. 
      So...not the carb
      Thought maybe vacuum petcock was bad, but there's no gas in the vacuum line going from petcock to carb and gas flows freely when on prime.  I even plugged the vacuum line at both the petcock and carb end and tried to run it with valve set to prime.  Gas flows freely, but does exactly the same thing.  I unscrewed the screw at the bottom of the bowl and gas flows thru carb and out bowl drain line when petcock is set to prime.
      So, I'm assuming petcock is good?
      Checked spark plug and it wasn't fouled.  Reset gap, didn't help.  Will swap plugs between Ozarks tomorrow but I don't think that is it.
      Anyway, that he history and now you're all caught up.  Scratching my head.  Valves? These were bought at same time and have had little use.  Suggestions?
      Thanks!   
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By Belmontie
      Hi bought a 2012 kingquad ASI last year a great machine which is a delight to ride, but I find sometimes it doesn’t go into top gear just revs high at about 42mph. Any idea ???

    • By pablo Blake
      Its in pretty rough shape and its gonna be my first atv, I worked on bikes before but nothing to do with quads. Anyways the quad has some problems and im tryna figure out what to focus on first. So the U joints i think are shot. The bike starts first try every time ussually have to give it a lil gas with the throttle and revs right up, idles fine but its running REALLY rich 3 starts and my brand new plug was pitch black

      Bike is L model

      video-1577465068.mp4

      Its using the original mikuni carb but im not the best at fixing the carbs and wondering if there is anywhere online that would be able to either walk me through it or help me with it i didnt see a air mixture screw so it seems like im gonna half to open it up and adjust like the float and a couple other things
  • Similar Tagged Content

    • By Chris Chitwood
      Hi, I’m a 16 year old that is wanting to get more into vehicle and mechanic repair. My dad has an old ‘96 Timberwolf that he doesn’t remember running since I was born. I want to get it running again as a memory for him and to help us be able to hunt together, and of course so I can learn how engines work more than the little information I know now. I’ve pulled the carburetor and gas tank off of it, and the carburetor is getting cleaned by a friend. I can post photos of the condition it’s in later, I’m just curious where I should start in my journey to get it running again. The power switch is broken off of the handlebar, so I am looking into fixing it, along with the pull cord. I’m afraid the engine is seized up, and I’m curious to hear any input anyone has. Thank you all.
    • By Craig Butterworth
      Hi, i'm looking for some help and advice with my arctic cat quad, its the first of the arctic cat quads as far as i know, manufactured in 1996 the bearcat 454. i have owned the quad for about 10 years now but just recently it has developed a problem with reverse gear, reverse wont engage any more like it used to 😕 the cable and handle is free but there is no movement the gearbox end, can anyone give me a heads up of what is involved to fix this? 🤔
      If anyone has a service/repair manual available for it as well that would be greatly appreciated! 🙂
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By katasha2
      I took apart the carburator to clean out and I can't remember exactly where the springs that are inside the float are supposed to go I've tried to look up schematics but I think I am missing a spring maybe need helpt:confused::confused:
    • By skgw1
      Feul pump went out. Replaced. At times quad cuts out like its not getting gas. Saw article on new pump needs to be calibrated. Told how to go into a service mode. Does not tell how to calibrate after going into mode. Can anyone shed light on this procedure.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...