Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Bearman

Shifter Problems

Recommended Posts

Long story short. I bought this off my neighbor and only has 3 gears. The part that holds the shifter rod on broke, this is on the inside where the clutch is. The rod moved out of its spot and when they welded it back together only has 3 gears. I have a new case for it just need to know how to get the shifter in the right spot before I put it back together. I am missing the indicator that shows me where neutral is. A link to a good Manuel would be great. Thanks

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Joe Dickerson
      I decided to replace the rings and piston on this machine because it looked like the plug was being fouled by oil. When I removed the right side of engine to inspect the clutch pack, I found 2 small round pieces with tiny expansion rings in the bottom cover. It looks like "clutch pawls" according to the illustration, but Id like to be sure. I saw that there are 4 of these in the new gasket set.
      Can someone help me here?
      I thank you in advance
      Joe
       
       

    • By Travis Johnson
      My 1988 Honda 300 fourtrax has a short all of sudden neutral light works but when I put on headlight nothing can't start it unless kick start please help
    • By Dale Kermes
      I need some help y’all, I bought a 450r, 2005 and I was riding it and unfortunately got stuck, I had no clutch control at all, I put it in gear and release the clutch, it doesn’t go anywhere, I select through all gears and it won’t move, i can rev it out, I just bought a clutch kit, but I am sorta new to this whole scene of race quads, I always had a 4x4, so any help will be much appreciated thanks.
    • By Ssg
      Hello! This is my first bike with a cvt it's a 19 Outlander 850 xmr. I use the 30" cryptid tires that come with the bike during hunting season since I hunt in a louisiana swamp and I have some 27" interco reptiles during the summer trail rides. So this past hunting season I got stuck and squealed the belt do i looking at cluch kits /adjustments to help with the low end but I dont want to mess with my summer riding so I'm looking for advice 
  • Similar Tagged Content

    • By Anthony Marceau
      Hi everyone! I have a 1986 yamaha moto4 200 that's been sitting for a while! Cleaned the carb, replaced engine oil, put fresh gas in it. Got it running and went for a ride! It was running great just a little backfire once in a while! I barely made it home on the way back and now the bike won't run at all since then! It will start if I give a little bit of throttle but dies instantly as soon as I let go off the throttle! And even if I try to rev it up it'll sound like its not getting enough gas.. it revs up a couple hundred rpm's and backfires through the carb.. it almost sounds as if I was trying to take off from zero in 5th gear! Nothing is seized though! I dissasembled the head and the piston and cylinder are fine! Rebuilt the carb, replaced the ignition source coil.. I don't know what to do anymore.. compression test shows 90 psi Specs are 128 psi but i'm not sure if I trust my compression tester.. any ideas? Thanks!!
    • By drifterss454
      im hoping that somebody could help me out changing my shifter on my 2014 outlander 400 max xt.,I kinda need step by step instructions,a brain aneurysm a few years ago has left me kinda useless sfiguring things out anymore,i think that hey took away the part of my brain that actually worked,lol,i did get the seat and plastics off,cover off the box,thats it,geez,i put more hurst shifters in my cars,cams,domes,cranksetc and now I cant figure out how to put a new shifter in my bike,more snow coming tonight,so, I"ll need my plow,,so I hope that somebody can guide me in changing the shifter,thanks all
    • By vedder37
      Title says it all. When I researched part it shows it does not exist anymore, discontinued. What can I do to stop the leak? Is there somewhere else I should be looking for part? The leak is coming from where shifter goes through seal, not around outside of seal between case and seal.
      Thanks.
    • By jprusha
      I have a 98 Timberwolf 250 5 spd. I would like to find a heel toe shifter and have been unable to find anything.
      Does anyone have any idea?
      Thanks-John
    • By blackbear
      I have manual450 honda atv hurt my foot bad,so can't shift,just wandering what anyone would say about installing hand shifter...I do mostly trails, try to stay away from mud etc.Thanks.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...