Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

rfcsvt

First ATV

Recommended Posts

Hello all!

This forum has already helped with a lot of the ATV related questions I have had so I thought I would say thanks and hello.

I just picked up what I believe to be a 1993 Big Bear 350 4x4. It runs but smokes a lot, and it left a fairly large puddle of oil on the floor after sitting over night. Other than that it seems to be in OK shape, tires are good and all the parts seem to be there except for the rear rack. Hopefully I will be able to get started on it this weekend.

Let the fun begin!

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Gary Ferguson
      My old Big Bear nearly left me stranded but I managed to limp back to my garage just before it died. Now No Spark. I’ve changed the obvious, inexpensive and easy parts- spark plug & coil without any luck. 
      Ive stripped it down and traced all of the related wiring, checking as many connections as I can but no luck again. 
      Next I pulled the cover and accessed the stator housing to inspect and do some resistance testing to ID a possible short. 
      Here are my readings:
      Source coil- 325 ohms
      Pickup coil- 225
      Can anyone tell me if these are good numbers, and if good, where to go next?
      I assume my next purchase will either be a new stator or CDI, but since neither of these tend to be returnable items I want to be as sure as I can I’m gonna get a resolution to the problem!!
      Thanks,
      Gary in SC
    • By Scott Matthews
      Just picked up a 1989 Big Bear 350 for $250 CAD. Bike was running but lost crank and spark. They've installed a new coil, a couple relays, and installed a Ford starter solenoid in place of the original. Now it cranks but has no spark so they sold it to me. Does anyone have a wiring diagram for this bike so I can test some wiring. Also any ideas as to direction to head would be nice. Lots of things have been hacked together so I know it probably wont be to easy. The ignition switch was replaced with a toggle switch, I already mentioned the Ford solenoid which 1 of the small wires was not re-installed, and a diode or something was removed from the oil temp sensor wire. I'm sure I will find more so a diagram would be amazing.
    • By crochet homemade
      I have bought a 1996 suzuki king quad 300 and I have noticed that it smokes but I have put oil in it and plenty of gas had to fix shifter bc the nuts and bolts came out somewhere. I have had to replace the wire for the starter but now when I try to start it it wont idle at all and when it does run it smokes really bad like a whitish blue I guess, and it likes to stall a lot. So anybody can help me out please and thank you

      10000000_310855426253462_714534016610467840_n.mp4
    • By Dave Ayoub
      Ok i am not quick to jump on a forum and post a question without doing my own part and trying to research and solve the problem myself but I cannot find any definitive information anywhere about my problem. I have a Big Bear 350 that I picked up very cheap which had been sitting in a field for years. I am not new to building wheelers but this one has me beat. After rebuilding top end and replacing the carb it fires right up. The vin has some number worn off from being next to the shifter but from the parts in the clutch i assume it is early since 87 parts seem to be the only ones that match. Thats when the plot thickened. 
      Reverse works fine but when in the forward gears it would not go past 1st and was hard to get into neutral. ie. a it took a million clicks up to thump into 1 and as many down to find neutral. still never getting past 1st. within minutes i could hear metal screeching and whirling around in the clutch side of the motor. I took the cover off to find that 3 out of the 4 springs on the centrifugal clutch had broken and were shredded. Also the black mechanism that the pawl on shift shaft grabs moves was loose so it wasnt always grab to change the gear on the transmission. I tightened that mech, and replaced the springs assuming it would solve the problem since the gears were not actually changing from the lever and the carrier should obviously not only have 1 spring left. 
      After putting everything back together it did go into 1st fairly easy but then i again couldnt get it back to N without a million clicks down and couldnt get it to go past 1st. I did one time get it into a higher gear who knows what one but i gained some speed and dropped rpm.
      If i jack both the front and the back wheels off the ground and run the motor it becomes much easier to shift and i can get it to run through the gears pretty well. Usually going into N without a huge fight. not perfect but it does hit neutral and roar while spinning the wheels instead of gain rpm and with the power. 
      I have tried every possible position on the clutch adjustment screw without any noticeable result. I think this could potentially be where my problem lies at this point.
      does anyone know if the case is supposed to be threaded? because mine is not. obviously it seems as though it should be since every other bike ive touched has been. i even took the cover off my quadrunner to make sure it wasnt crazy.
      when the screw is adjusted and the jam nut tightened the screw will just slide back out since there is no threading in the case. accomplishing nothing. 
       
      Does anyone have any insight on any of this? Are my plates stuck, Centrif clutch worn out, case stripped or something else crazy im over looking? 
       


    • By dbconn55
      Hi guys I have a 2003 Arctic 250 4X4 it starts idles and runs great for about 10 min. then it spits and sputters and dies but it starts right up like nothing happened idles good till you give gas and it does it again let off the gas and it's idling great again this goes on for about 15 to 20 min. and then it takes off runs good all day like nothing was wrong.
      I cleaned the carburetor it looked like a new one inside found a little gunk in one orifice, new air filter no crimped lines air line to tank good I did put a meter on the battery idling it said 16.5 V that's high I think would a voltage regulator cause this?
      Suzuki shop wanted to sale me a stator for $556.00 but said it could be something else also thought I'd see what you guys say about it
      Thanks
  • Similar Tagged Content

    • By Sombeech
      I shot this footage last weekend. We ran a Honda Foreman along the beach and had a great time wakeboarding.
      Helmetcam footage.
      There is also a download link for the YouTube Challenged employees at work.
    • By Arizona
      Went shopping on Saturday, picked up another Kawasaki Bayou 220 and a Yamaha Timber Wolf 250
      I really should sell some of these but they are a lot of fun to find, fix and ride
      Of course neither of them run but that's part of the fun!  Az



    • By oxidized_black
      these are what i have in my collection ... always looking for more
      Linhai (german)
      http://rapidshare.com/files/3880403675/Linhai%20(german).rar
      Linhai 250 - 360 Service Manual
      http://rapidshare.com/files/582921063/Linhai%20250%20-%20360%20Service%20Manual.pdf
      Linhai 260 - 300 Parts Manual
      http://rapidshare.com/files/1587211864/Linhai%20260%20-%20300%20Parts%20Manual.pdf
      Linhai 260 - 300 Service Manual
      http://rapidshare.com/files/3400427719/Linhai%20260%20-%20300%20Service%20Manual.pdf
      Linhai 300 Parts Manual
      http://rapidshare.com/files/1938660329/Linhai%20300%20Parts%20Manual.pdf
      Linhai 260 Service Manual
      http://rapidshare.com/files/218261873/Linhai%20ATV%20Service%20Manual.pdf
      Linhai Bighorn CUV Service Manual
      http://rapidshare.com/files/2459140573/Linhai%20Bighorn%20CUV%20Service%20Manual.pdf
    • By Zacharia Maisonneuve
      i have a 1993 timberwolf yamaha and the compression is good and lights work but for some reason the electricity is not going to the spark plug(s)! i got a friend to check it out and they said its no use but im not giving up! please help with this!
    • By Connor Tuftin
      I have a 1988 300 Honda FourTrax, All wheel drive.
      My brother and I were fixing up this quad. We put a brand new battery and fuses in and it was running fine until we put the quad into reverse. As soon as it was put into reverse all of the electrical cut out and power wasn't making it to the head unit anymore and both of the brand new fuses popped. We figured there might have been a short from the starter or solenoids, but they are all working properly. At this point we don't know where to start looking for where the short could be. I'm just wondering if anybody has had the same issue or knows of similar issues that could cause these electrical shorts?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...