Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

mrmike

An important notice to Polaris owners, esp Diesel Rangers

Recommended Posts

If you have been affected by clutch/shifting problems with the 2011-2014 Polaris Ranger Diesels, or any other Polaris UTV's or ATV's, please see the following thread:

Ranger Diesel Nightmare - RangerForums.net - Polaris Ranger Forum

You are far from alone. There are hundreds if not thousands of other people who are affected by this same issue. The only half-proven solution is to buy an aftermarket clutch for $1500 from a separate company, which is conveniently founded by an ex-Polaris engineer.

In addition, the sticking clutch eventually leads to catastrophic transmission damage. I paid $12,000 for a Diesel Ranger in 2011, and it has been difficult if not impossible to shift for the majority of its life due to a factory-defective clutch. The sticking clutch wears out the transmission, and eventually you will be faced with a $2500 bill to have it replaced.

If you or anyone you know has been affected by this clutch, please visit the thread linked above and make your voice heard.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By 06kfx440
      It’s been a pleasure serving all of you. I can not ride anymore. My illness has turned to the worst and I can barely walk anymore. I will still be here helping where I can. I might just get an oddsey and work the sh!t out of it. But I’m done. I didn’t want to be in this situation. But I have to take it. It’s been so much fun here guys!
       
       
      Sent from my iPhone using Tapatalk
    • By colin james
      View File 2018/2019 Polaris Sportsman XP 850/1000 Service Manual
      This is the factory service manual for the 2018/2019 Polaris Sportsman XP 850/1000
      Submitter colin james Submitted 08/01/2019 Category Polaris ATV  
    • By Jeremy Morris
      If you're getting that pesky leaky seal on the pinion of your front differential and the pinion has allot of play, polaris won't sell the bushing needed to repair it properly without having to shell out big bucks for the complete ring and pinion kit. 
      I have a kit with an upgraded bushing, Japanese made bearing and USmade seal
      50 shipped in the US and 55 to Canada

    • By Chase Cook
      I have a Polaris sportsman 500 and I just replace the piston in rings and head gaskets on it and I made sure the timing was exactly right it's getting gas and fire but it still won't start. It sounds like it has low compression but at the same time it sucks in air pretty good from the intake. Also the valves are adjusted to spec. It did start the first time I installed the Piston and Rings but it only stayed running for 5 seconds with starting fluid and then it shut off and then I tried to turn on the next day and it didn't do nothing and I've been going at it for three weekends now and it still ain't doing nothing. I wonder if i set the timing off a little or a lot if it would start up, because I inline the crankshaft sprocket with the crankcase timing line like it said in a manual and the two points on top of the cam sprocket to top dead center of the piston. I even took the spark plug out and stuck a camera light in there to make sure it was top dead center and it still won't do anything. AlsoI drain the carburetor some and shut d fuel petcock off to see if it was getting too much gas and that still isn't the problem. And where I live all the darn mechanics that work on Polaris ATVs are booked for two weeks which sucks and I need hope immediately or I'm just going to set the ATV on fire because I'm getting very frustrated with this crappy brand. Every other name brand ATV I worked on I got it running right and I replace the piston, rings and everything etc, and they started up fine. But this is starting to get very frustrated and I don't know who to talk to who had this problem before, who "don't have to come look at it". Cuz when they say that that means you're not going to come look at it until 2-4 Weeks later because there booked, which I don't have time for. Living in northern part of Florida sucks.
  • Similar Tagged Content

    • By colin james
      View File 1999 Polaris 500 Diesel Service Manual
      This is the factory servicefor the 1999 polaris 500 diesel 
      Download all the chapters for the complete manual or just download the section you need 
      Submitter colin james Submitted 09/05/2018 Category Polaris ATV  
    • By colin james
      This is the factory servicefor the 1999 polaris 500 diesel 
      Download all the chapters for the complete manual or just download the section you need 
    • By Beb1041
      Looking for a download of a manual
    • By warkcol
      I am having an issue where it sounds like the gears are slipping if I hit the throttle really hard and also after letting off when the engine brake is applied. Also, the drive train that goes to the front also rides again the gear shift box. I will attach pictures and a video here shortly.
      Thanks in advance!
      [ame]
      [/ame]https://postimg.org/image/cdlu6fza9/
    • By Weldingrod47
      Trying to change front wheel bearings. I removed the cotter pin and castle nut. Hub won't budge. Is there an additional retaining clip? Seems to be one of those push on type that barbs on the thread of the spindle. How do I remove it?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...