Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

GOODY37

99 kawasaki prairie 300 four wheeler ignition question

Recommended Posts

I have a 99 kawasaki prairie 300 4 wheeler that was stolen from me, and i recently got it back. It had been hot wired, and ignition busted out. I need to know what are the color of the wires that connect to the ignition switch? Thanks in advance.

Share this post


Link to post
Share on other sites


Hi. At least you got it back!

It's not a model that I'm familiar with but midwestmanuals.com has a downloadable pdf that seems to have a vast amount of info on Kawasaki quads. This includes wiring diagrams for everything since time began. [Maybe I exaggerate a little bit there.]

The wiring on these things seems quite simple. Good luck.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By mike costa
      Motor starts right up, but when I open it up past quarter throttle it bogs way down while ridding, the longer it runs the worse it gets. If I just leave it in neutral and  give it full throttle it revs up and down. 
      Back history:
      Bike sat for 3 years,
      Installed new plug, cleaned the fuel tank, took it to a shop and had the carburetor gone though.
      Picked up from shop, motor bogged down first day and barely got me back to the truck an 1 mph.
      Took back to shop after a month I was told it had a bad plug, I told him I just replaced it.
      Got quad home and it is doing the same thing!!!!!!!!! 
       
      Thanks in advance for your support!
       
      The carburetor has recently been gone through by a shop
    • By Sonders
      It appears that the Service Manual thread at top of forum is dead as all the links no longer work.  I'm actually looking for service manual for a 2000 KVF300 Prairie that I just picked up.  Does anybody have link to one that they can share, or know where I can find one?  Thanks in advance for any help.
    • By Steve Howard
      Ran find shut down the quad next day would start and idle when you try to accelerate it would start popping through the carb got a rebuild kit soaked it in chem clean after break down for 12 hours on slow vibrate reassembled and adjusted per manual still the same thing any help would be really appreciated thanks and happy ridding  
    • By MarkinAR
      Let me start with I have about 30 years of ATC experience, but not much with stuff made after 1988.  Some, but I'm mechanically inclined so it's all good.  I"m rehabbing a 1997 Bayou 220 to send back into the wild and the mechanicals are now all good, just working on making the electrical system...electric.  Right now, I have no power on the white wire as tested directly on the plug at the starter solenoid.  I'm assuming that wire is supposed to be hot any time it's attached to a battery?  The genius that had it before snipped a couple wires and inserted a fairly heavy push button for electric start bypassing the electrical system. I think i've corrected everything north of the solenoid but the white wire has me stumped.  Is my assumption that this should always be hot with a hot battery correct?  Does this indicate a broken circuit in the starter solenoid?  Relay was also bad and wired incorrectly, but that's resolved and I can make the relay click bypassing the solenoid and connector, directly giving the white wire 12V.  Thoughts?
    • By Dimelol
      I have a 2003 Kodiak 450 that i purchased a while back with around 300 hours on it. It has never ran right from the beginning. Initially i thought it was just a carburetor issue because it was all clogged up from sitting for months. It has been cleaned, rebuilt, and taken off probably about 10 times troubleshooting this problem. I have quadruple checked everything including float height ect and it is set correctly, the jets are also brand new, needle and seat have been pressure tested as well. So after all of that I am convinced that the carburetor is not the culprit. I have an issue where the idle is very choppy, almost as if it is misfiring with a rich condition on top of that. I can use a brand new plug and run the machine for just a few minutes and it will be a dry and and coated in black carbon build up. The exhaust also has a strong smell at idle. I had trouble restarting it when hot for a while, but i adjusted the valves and it seemed to solve that issue. They were both way out of tolerance (tight). The weird thing is, outside of idle it seems to run pretty well. 
      So with all that being said I have ruled out the carb/valves/compression and moved on to the ignition and this is where i have a few questions about factory specifications. I guess the main question I have is, how strict are these tolerances? And could them being off by this amount cause the issue I am having? Do all three of these parts really need to be replaced? I would like to know before I spend the money on these new parts, and it not fix my problem. Below I will list what the specs were in the service manual along with the reading i got.  This is my first experience testing ignition components. I just found it odd that all 3 are out of spec according to the service manual.
      Spark plug cap resistance: 10 kΩ at 20 °C (68 °F)
      My Reading: 8.90 kΩ
      Primary coil resistance: 0.18 ~ 0.28 Ω at 20 °C (68 °F)
      My Reading: Fluctuated between 0.4 - 0.5 Ω
      Secondary coil resistance: 6.32 ~ 9.48 kΩ at 20 °C (68 °F)
      Reading was within the specified range.
      Pickup coil resistance: 459 ~ 561 Ω at 20 °C (68 °F)
      Reading was within specified range.
      Rotor rotation direction sensing coil resistance: 0.085 ~ 0.105 Ω at 20 °C (68 °F) 
      My reading was 0.3 Ω
  • Similar Tagged Content

    • By Ashton Crawford
      Hello everyone, i have 2000 Polaris Trail Blazer 300 I’ve been stumped on for weeks. I’m having a lot of issues starting the quad. I cleaned the carb spotless because I thought it was a carb issue and bought a new fuel line because it wasn’t getting fuel. The carb gets fuel perfectly fine now but it won’t start. The spark plug I a little worn out but it’s good enough for just one start. The only time it does “start” is when I spray starter fluid into the carb. But it never stays on. It’ll start for a bout a second then just die out immediately even if you’re giving it some throttle and the choke is on. I have no clue what I should do. If you need more information, have questions, or have any slight idea what the issue would be and how I could resolve it. Please reply ASAP. Thank you.
    • By Alan Callison
      OK ya'll.My son bought this thing and was told its a Kaw Bayou 300. Maybe. I cant find any numbers on it.The one tag I did find its so faded as to be unreadable. Its a long shot but maybe someone can help ID it. Thanks in advance.









    • By Jeff Wharton
      I have a 2000 Arctic Cat 300 4 wheeler. I have been having some carburetor issues. So i bought a new carb. Now I'm having these issues. The unit will start and idle fine, when i go to accelerate it wants to cut off. So i checked to make sure it was getting gas and the fuel filter will be full of gas and then once the carb opens the filter drains down and will not refill quick enough to run. So i checked to make sure gas was flowing to the filter and it is flowing fine through the line. I remove the filter and run the gas line directly to the carb and the engine idle fine and then it will run good as i ride it for about 10 minutes then it will start with the same issues again i cannot accelerate enough to move the 4 wheeler. Every time i accelerate the unit will cut off. What is wrong with this thing. My 400 Arctic Cat is doing the same thing except it will backfire, I'm lost i have tried everything i know to do, what am i missing here. Thanks for your help
    • By Maurais
      I’m looking for new replacement shocks (front & rear.) on my 1997 Kawasaki Bayou 300 2x4. New OEM shocks are upwards of $400. I haven’t pulled the rims off to check the eyelet to eyelet length but I’m hoping an expert on this site does know( I called Kawasaki direct yesterday and they were of know help.) Any technical help would be appreciated. TY fellow members. Vic
    • By scottj11
      Hello, how are you'ns doing? I'm in the process of tearing my Kawasaki Bayou down to fix a rattling noise and an oil leak. I'll probably be asking questions about this project. My step-son has an Arctic Cat 300, he was riding yesterday and when he turned it off it was running fine, but it won't do anything. The lights come on but it won't turn over or anything. Does anyone have any ideas on what might be wrong? TIA
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...