Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

cody52119988

Kolpin 90cc No spark

Recommended Posts

hi im new to this page and i was wondering i have a kolpin 90cc atv that i got through a trade for a snowblower. It obviously sat in a mud puddle for awhile the stator was full or mud and crap but is now clean and creating current it also has a new cdi and coil but still no spark any ideas?

Share this post


Link to post
Share on other sites




I dont have any manuals for your machine and dont know how your ignition system is setup but I assume it is like all others. Since you had problems with the stator I would check the pick up is getting the pulse from the rotor to signal the CDI to juice the coil.

Also check fuses, wiring and grounds are good. Particularly check connectors for dirt and corrosion.

Do you have a wire diagram for this?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By jim estes
      Got this terrapro recently. Has slight damage on left front fender-traight otherwise. Low hours-no smoke-runs excellent!! Finish mower comes with it. Mower has no issues. asking $1600. Always open to partia; trades. This is a neat machine that starts runs and drives very well!  If your interested shoot me a message  




    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By Brian Simmons
      I am looking at a 90cc Arctic cat 90cc not sure what year right off hand . The shaft broke off right outside the motor . Can anyone help me ? What do I need to do to fix it ? Do you have any pictures or videos ? Let me know ?
       
    • By Frank Angerano
      I would like to hear who uses what to clean there ATV’S. 
      I’ve always been a fan of simple green and it’s always worked well but with this new property and the crazy black mud and clay that’s there  I have to say the simple green is not cutting it. 

      So from cleaning  right after a ride to cleaning them when you find one in a barn I would like to hear what everyone does and what your recommendations. 
      I’m looking to try something new.  
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...