Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

kris660

Need some help with a 660 Grizzly Please

Recommended Posts

I have a 2002 grizzly 660. I just bought it last week. It had sat for about a year. I knew going in that I was going to have to spend some time in the carb.

I took the carb apart and sprayed it with carb cleaner and blew it out with compressed air. I cleaned out the fuel tank, replaced the fuel line and new fuel filter. Filled with fresh fuel.

Started it up and set the idle. I rode it for about 3 hours yesterday. Then it developed a miss. At idle it would go put put put miss put put put miss. If I didnt not add some choke then it would die. The miss wouldnt go away it would just idle it up fast enough for it not to die. It progressivly got worse. It also would have that same miss at slow speeds steady throttle. If you give it lots of throttle it runs great and the miss seems to go away. When it misses like that the exhaust makes a whistle sound also.

Today I pulled the spark plug and replaced with a new one. It did not help. old plug looked good, but it was two heat ranges to hot from stock. Not for sure why that was in there.

My first thoughts would be the pilot jet maybe. Pulled it out and its clean.

Is it possible that some trash got in there with all new lines,filter,fuel and a clean tank.

Thanks in advance guys, kinda stumped.

Share this post


Link to post
Share on other sites


Values? Maybe new values or they need adjusted? I dont know. Maybe run compression too.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By StolenATV
      Taken from my car port around 0330 and was taken by at least 2 people found footprints pushing the quad all the way to the road (80 yards)
      The post 2012 Yamaha Grizzly 700 EFI 4×4 Stolen appeared first on STOLEN 911.
      View the full article
    • By K L Buck Naff
      Trying to replace the carburetor on my 2003 Bear Tracker 250. Two brand new carbs in a row from different suppliers.   Both leak fuel out over flow and intake as soon as I turn the gas on. Any ideas. Am I doing something wrong?
    • By Daryl Mann
      Hey new to the page 
      having an issue with my carb slider jamming ect just replaced the carb with a good pre owned unit and seem to be having a similar issue 
      is there a home fix for this as a posed to buying yet another carb as the quads my daily transport and stuck without it 
      thanks for looking any help great full can also forward video of the problem I’m having if needed 


    • By Ellery Zandt
      I have no idea where the antifreeze line coming off the thermostat goes too. The carb two nipples in the pic create a vacumme. Can someone help me on this please....!!! my email direct is [email protected]!!!!
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
  • Similar Tagged Content

    • By Ajmboy
      This is more of an informational fix I wanted to share..
      My Grizzly has been getting harder and harder to shift this winter and today was completely stuck and I needed to plow the few inches that came down this morning. First thought...oh no, tranny...but it’s winter and maybe it’s iced up. I pulled off the plastic to see what was going on and indeed I did find the drain tube iced up. 
      I took the blow dryer out and de-iced it. Quick fix, I never really thought about the shifter drain tube icing up before, shifts like new!



      FA04AC3B-4FB0-4764-AFD9-1492F5CC790B.MOV
    • By Matt Dyche
      Can anyone give me guidance on my issue. I have a 02 Grizzly 660 and replaced the wet clutch, primary shaft, one way bearing.  Today I was riding since I tested and was driving about 20-25 mph and all of a sudden the tires locked up, heard a screeching sound, and engine died.  Didn’t have a clue what was going on, decided to try and restart, engine turned over normal but engine hesitated slightly, started and had to assist with the throttle.  It seemed to do this for a minute then seemed to straighten out.  Got home, pull clutch cover and test drove to witness clutch operation and everything looks and sounds perfect.  Could not duplicate.  Please help. 
    • By gyminis
      HELP, i have a 2009 yamaha grizzly 700 yfm7fgpy special edition with a defective fuel pump and am wanting to know how to test it to know if it is defective or not
    • By gyminis
      i have a 2009 grizzly 700,replaced the fuel pump and filter,replaced the spark plug and checked the air filter for a mouse house! it runs then shuts down,wont stay running,does the fuel line need to be primed and air free to run properly or am i missing something obvious??????????????
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...