Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts



You can get replacement boots or CV joint rebuild kits from the online parts suppliers or Ebay. Good quality axles are expensive, but I would not use cheap replacements.

Share this post


Link to post
Share on other sites

Motosport, bikebandit, cheapcycle, are some of the more popular online suppliers. EBay has good deals too.

Sent from my Z10 using Tapatalk

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By RCNY1
      Seems impossible to find a pair of front shocks for my 02 Yamaha Kodiak,newer or older listings are they the same as a big bear ?  Factory are $245 each !!! Any help appreciated 
    • By Jeff011366
      Hello,
        Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
       
        My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires....  Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
        It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
       
      Thank you in advance for sharing your knowledge.
      Jeff
    • By w_r_e
      Can anyone point me to a good set of instructions for changing front diff oil on a 1987 Suzuki LT4WD? I can almost guess which bolts are drain & fill... but I've been wrong before... 😆 
      I found some partial posts on other forums and they linked out to dead images and whatnot. Any help appreciated. 
      This thing is running pretty good, got the front brakes back to life, electric start works fine, seat cover fixed up, plastics stitched back together...
      BEFORE (last week):

      AFTER (today):

    • By Jeni Lynn
      2012 Rancher ES-- only when driving in 4x4 when I get to about 15-18mph there is a loud clunk in the front end and a hard downward jerk. Its almost as if its trying to downshift itself. It doesn't do it in 2 wheel drive.  I have checked the angle shift sensor and applied dielectric grease to it, changed the front end differential fluid (the old still looked good and clean) checked and adjusted the clutch. Hopefully someone can give me some more ideas. 
    • By Mudrecon
      I'm working on a 95 300 kingquad and wondering about the aftermarket carbs. There sure is a price spread -is the OEM recommended or is 'cheap' ok.Off shore are way cheaper but is the quality that bad
      Thoughts

  • Similar Tagged Content

    • By Jean de la Chevrotière
      View File Polaris 700 2002 Owner's manual
      Polaris 2002 700 Owner's Safety and maintenance manual
      Submitter Jean de la Chevrotière Submitted 12/01/2018 Category Polaris ATV  
    • By Jean de la Chevrotière
      Polaris 2002 700 Owner's Safety and maintenance manual
    • By priglmeier
      I own a 2002 Can-Am Quest 650.
      It will start if you massage the throttle a bit and it will continue to run. BUT if you let go of the throttle and try to let it idle it will always die warm or cold.
      It has Non-Oxy premium gas, a new gapped NGK plug, a new carb (as of today) and fresh fluids. After installing the new carb it runs exactly the same.
       
      I only have a few things that I have observed since the new carb:
      The choke still doesn't do anything. It has a good cable and it is hooked up. It on fully off. There is a cable in the top, front of the engine that splits into two connectors. The connected side is in the photo. The other side has the yellow banded section and is not connected. I do not see anything in range of this connector so I don't know if this is normal or not??? The original carb wasn't really dirty or clogged. I'll use it as a spare. I don't see this cable and connectors listed in the Can-Am shop manual. Looking for some help. I want to ride!


    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...