Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

tundrawolf

1991 King Quad slide has holes in it?

Recommended Posts

Hi, I have a 1991 King Quad that I bought that needed "carb work". So I bought a rebuild kit and installed it, checked and set float height.

It idles okay, but when I give it gas it stumbles all over itself. On full throttle it suddenly comes alive and pulls and pulls.

It is rideable, but only marginally.

So I was examining the slide and diaphragm, but at the bottom of the slide, there are three holes. One in the middle for the needle, and two on each side of it at the bottom of the slide.

What are these holes for? I can see daylight through them so no vacuum is being formed in there, it is being sucked out of the two open holes. Is there a spacer or something that blocks these holes? I might try filling them with silicone and seeing how it runs with it in there, because it is not running right right now. It acts lie there' no vacuum pulling the slide up, only at WOT.

20150106_183741.jpg

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By raybob
      I have it all but can find where the vacuum line on the carb goes its a 2000 suzuki 500 quadmaster I know where the two vent lines go but not the bigger vacuum line goes it has vacuum on this line. need help. Ray
       
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By JCH
      Hi there
      I am in need of a manual for my KLF 300 Bayou 4x2 . I've found others on here for the 4x4 model, but was wondering if I need a separate 4x2 manual. Does anyone know?
    • By mrfartsalot
      i have a 1986 yamaha moto 4 200 and was wondering if i could put a 350 or 300 jug and piston on it to bump up the cc?
    • By StolenATV
      1987 Suzuki LT 80 and 2007 Honda CRF 50 dirt bike stolen out of my driveway on July 4th. Anyone with info that recovers them will get $400 no questions asked.
      Thanks
      The post Suzuki LT 80 Quad And Honda Dirt Bike appeared first on STOLEN 911.
      View the full article
  • Similar Tagged Content

    • By Danny Ouellette
      Hey guys! I only need a couple think from the machine. Front bumper is #1. The other is the front plastics in grey. Used is fine as long as there is no cracks. 
       
      Thanks,
      Danny

    • By Martin Carrière
      Recently bought my BB. Everything works great. Only thing is, each time I put it in reverse, it either starts to rev high and start moving without giving it gas or I'll give it a bit of gas and let go and it will still rev at the same rpm or higher and keep moving. Doesn't do it for high or low.
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By katasha2
      I took apart the carburator to clean out and I can't remember exactly where the springs that are inside the float are supposed to go I've tried to look up schematics but I think I am missing a spring maybe need helpt:confused::confused:
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...