Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

cherpe

2002 Honda Foreman 450es - Reverse Issues

Recommended Posts

I have a 2002 450 foreman es. When doing several shifting into reverse like when plowing it starts to become troublesome to get back to a foreward gear.Have to keep pressing the shift buttom several times to get out of reverse.Has anyone had this issue ?Is there a fix to this problem? Thanks

Share this post


Link to post
Share on other sites


Take the (angle) sensor off and clean it with a q-tip and pressure spray it with a can of compressed air-dust cleaner. It's a bit of a challenge getting to it ... there are only 2 bolts that hold the small metal cover over the sensor and 2 bolts that hold the sensor on. Also clean the small rubber seal-ring inside as well, make sure you don't lose it when you take the sensor off and also clean the sensor wire connection plug and put some dielectric grease on it.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Michael Rogers
      Anyone ever replaced the shifter shaft on one? Not sure on the year but assuming it is in the late 90's. Is it a huge task, splitting the case etc... thinking about buying it as my next project.
       
      Thanks
    • By scot91
      Hi guys im new to the forum and i hope i put this in the right spot. But im putting this up for my uncle. But he has a 2002 Bombardier quest rotax 650 4x4 All wheel drive. Now i was driving it down the road today and all sudden it shut down i thought it ran out of gas but it didnt. After it shut downi pushed it to the side of the road and tried to crank it over but it wont crank over. It is a electric start none of the lights or anything work So what i was thinking its in the wiring somewhere right? Does any one have a website that has a wiring diagram for this 4 wheeler or does any one know what else it can be? If anyone has any idea please let me know everything willprobley help thanks guys!!!
    • By flyinbrian365
      View File 2002 Polaris Magnum 325/500 Service Manual
      2002 Polaris Magnum 325/500 Full Service Manual
      Submitter flyinbrian365 Submitted 05/14/2020 Category Polaris ATV  
    • By Nick Brooks
      Working on a 2002 Quest 500 and the grommets in the tank are rock hard and leak.  Any tips on replacing without having to pull the tank, hands are too big to get to the bottom gromment which is the worst one.
  • Similar Tagged Content

    • By Flanstone
      I just bought two 1985 TRX250's from my father-in-law. One runs great, the other not so much. The one is having issues with the shifter. The shifter seems to be resting lower than normal. When I press the shifter downward, it just pops back up. Any thougjts as to what the issue might be?
    • By Anthony Marceau
      Hi everyone! I have a 1986 yamaha moto4 200 that's been sitting for a while! Cleaned the carb, replaced engine oil, put fresh gas in it. Got it running and went for a ride! It was running great just a little backfire once in a while! I barely made it home on the way back and now the bike won't run at all since then! It will start if I give a little bit of throttle but dies instantly as soon as I let go off the throttle! And even if I try to rev it up it'll sound like its not getting enough gas.. it revs up a couple hundred rpm's and backfires through the carb.. it almost sounds as if I was trying to take off from zero in 5th gear! Nothing is seized though! I dissasembled the head and the piston and cylinder are fine! Rebuilt the carb, replaced the ignition source coil.. I don't know what to do anymore.. compression test shows 90 psi Specs are 128 psi but i'm not sure if I trust my compression tester.. any ideas? Thanks!!
    • By dboy910
      Ok new to group and new to quads. I picked up a 88 Big Bear for next to nothing but it has issues. The entire high low revers shifter has been removed. All I have is a bar attached to the linkage. I can shift into all three but I would like to replace or get suggestions. I have looked around but there is limited info or pictures on what I would need to buy or where it even mounts. Any pics of what where and how it works would be great. Or direct me to correct thread.
      Thanks
    • By tmaterman
      Hi guys! First post here...bought a Bruin, as mentioned above from a buddy. It had been parked for a few years at his house..unused. Bought it from him at a steal and put a battery in it, new gas, etc...fired right up. It is cutting out now, but I suppose that is just the carb/fuel system needs a good cleaning. Ordered a new carb and hope that gets it going good!
    • By EASTER467
      I have a 97 polaris sportsman 500 and the 4x4 dosent work in reverse. It works in forward high and low but when i put it in reverse it kicks out. Ive tried pushing the override button while engaging reverse but it still dosent work.any ideas would be greatly appriciated.thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...