Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ddiggerr

Rough Idle issue - video included

Recommended Posts

1983 Yamaha YT175

Fired up for the first time after total rebuild. Now I have no idea whats going on. Compression is 120, new plug, new fuel and oil lines, new choke and fresh fuel. Carb cleaned and reeds are good (no gaps).

Will not start without choke and stalls out when choke is off. Played with choke adjustment and doesn't change.

It fires up first pull and only idles if I play with idle screw. As soon as I touch throttle, it goes bezerk on me and I have to shut it down as you can see in video .......

You can here the recoil lever tinging in the video. I lost the spring. D"oh!!

So far I have swapped ignition coil, spark plug, CDI with no change. I have removed flywheel to check keyway and it is where it should be.

Checked resistance on stator ... I get 10ohms +/- 10% on pickup coil within specs as per manual and I get 273ohms on charge coil. Manual states 300ohms +/- 10%, so that is also within spec.

I have also swapped out jet needle and played around with different settings. Eventually I put it back to the 3rd line.

The engine already has new seals and bearing so I am completely baffled as to what I am missing here.

Any takers?

Any and all suggestions will be appreciated.

Thanks

I have also swapped carbs from a running YT175. Same results.

Edited by oxidized_black

Share this post


Link to post
Share on other sites


I went out today to look things over. Someone mentioned to check the flywheel (magneto) to see if it different than the one from the running trike. I actually have three.

So, I put all three side by side to compare and they are identical. Next I decide to see if maybe one of the wires from the stator was rubbing and was shorting out. Nope nothing there. After going back and forth between the 2 trikes looking at the stators, I noticed that the pulse coil and source coil was installed differently on the freshly rebuilt trike.

When I put everything back together after cleaning off the crud, I had the wires facing out on both of them, and they apparently need to be facing in. That is one thing the manual does not show. I had actually installed them backwards.

I put everything back together, primed it with a shot of carb cleaner, because I don't have the air box on yet, and it fired up. I threw on the plastics and took off out of the garage.

Now I just need to take care of the exhaust leak where the pipe meets the engine.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By Asen_77
      Hi All,
      My name is Asen and I am from Eastern Europe, Bulgaria. Riding a Yamaha Raptor 700R and this is my first Quad wanted for a vey long time :)

       
    • By Jordan Ritzman
      What are some good online vendors for parts
    • By David Barsukoff
      Hey, I just bought the kids a LT80 and noticed a small puddle under the machine after they were riding it for a bit. I'm wondering if anyone knows why the fluid coming from the fuel shut off is a red colour, and would have any ideas of where this issue is coming from? I haven't had a real good look at it yet, thought I would ask first. 

    • By John Ford
      i ordered a keihin carb for my 07 trx 90 and it fits nicely but the new cable they sent is way too long and i can't make it work.  the old honda cable cap [that fits on top of the carb] is too small to fit.  the keihin cap is approx 3/4 or 19mm.  honda cap is more like 1/2 in.  the keihin has a rubber boot on the cap where the throttle cable goes through . i don't know how to find the right length [most cites don't give the length].  i'm not sure how cables fit into that boot  and do i need to add the length of the boot to the cable?  the old honda cable is 28 inches total, but the cable movement is only approx 2'' which would not be enough to reach the actuator block on the keihin.  looking to find a throttle cable compatible with the keihin.  any help, please.
       
       
  • Similar Tagged Content

    • By Williejoe Neckbone
      Have a 400 4×4 have cleaned carb niow when u start it u have to have choke on and when u kick the choke off the engine speeds up then dies like it's not getting fuel plz helo
    • By Ray Roberts
      Hey everyone im new here, i have a problem with my 2001 suzuki quadrunner 500. When i start the bike up it sounds fine but a few seconds later the idle speed just keeps rising to where you cant put it in gear, and if im lucky it will climb down to where i can put it in gear but when i press the gas it immediately want to die. Please help me!
    • By Scoopeddad
      So I have a 1994 Honda trx300 and I still am having some carb issues. I cleaned the carb and installed a new carb kit. Starts great, idles great, but when in 3rd it seems to pulsate. Not steady power. Any ideas on the setting the setting for the carb? I put a new spark plug in and the old one did seem pretty dark and sooty. I checked the gap on new one and installed. Went for a ride and it didn't seem any different. Any suggestions would be great..
    • By johnwayne
      i have a 2000 suzuki king quad lt-f300f that i picked up as a project bike. it didnt run well when it was parked outside 5 years ago. it cranked after putting fresh gas - but would not run below half throttle, i took apart the carb, cleaned debris, and re-assembled. i suspect that the pilot needle is sheared off - it never protrudes into the throttle body through the pinhole. now to get the bike to ALMOST idle, the throttle idle adjustment knob is all the way up/in. the pilot needle is turned almost all the way in/up (if i understand correct, it should nominally be out 2 1/4 turns or so). and like i said, it will ALMOST idle. floods easily, rides rough.
      wanted to hear from those more experienced than me with suzukis - and im self-taught atv repair, so dont laugh too hard if my verbiage/part names is way off. 
      facing the driver's side of the bike [US] there are three hoses on this side of the carb. without a service manual or way of knowing what was messed up before i got it, i think i have them right: front hose as a vacuum to the petcock, middle hose as vacuum to the fuel pump, rear hose as fuel line from the fuel pump. running the bike in prime position results in flooding even while riding. with all hoses disconnected from the carb, fuel slowly drips from the vacuum line connected to the petcock.
      so just my speculation is that the diaphragm in the petcock is split, and the pilot needle is broke off - causing my inability to not quite idle and the rough ride. this suzuki is hoses and cables everywhere compared to the honda ranchers and yamaha warriors i am used to. I would like to have a plan rather than: replace everything at once.
      is my speculation on the right track, or could something else be at play? say, if the compression was non-existent, would that cause non-idling? i am all ears, look forward to the input.
    • By Bubba Blaster
      Hi there, new owner to a Bayou 220 and could use some input from those who have owned these. At idle only, I am hearing a distinctly noticeable amount of chatter noise coming from the lower right side of the engine - right in the the clutch housing area. It's like a light clanking sound like something is loose in there. It goes away as soon as you give it throttle. Shifting in and out of gear is smooth and there is no change in the noise if you have it in or out of gear. The clutch doesn't slip at all, it's just that noise. I can also feel it when my hand is on the the clutch housing.
      I just replaced the oil and filter with 10w30 motor oil per spec. Any thoughts?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...