Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

tsylvester

1993 Yamaha Big Bear - Aftermarket Stator

Recommended Posts

hey everyone I have a 1993 big bear 350 that I got an after market stator for it but there was no plug on the four main wires. I was wondering if anyone could tell me which wires go where on my bike. From the bike I have red, blue, yellow, and white/green, and from the stator I have green, brown, red, and white. If you can tell me thanks.

Share this post


Link to post
Share on other sites


I know off the stator red and white are from the pickup coil but don't know which wire colors to connect them to

Share this post


Link to post
Share on other sites


in the yamaha atv section, there is a service manual thread and i think the 3rd post has the manual ... i am pretty sure it has an electrical diagram(s) ...

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By K L Buck Naff
      Trying to replace the carburetor on my 2003 Bear Tracker 250. Two brand new carbs in a row from different suppliers.   Both leak fuel out over flow and intake as soon as I turn the gas on. Any ideas. Am I doing something wrong?
    • By Hondasher
      I picked up a 1997 Yamaha Big Bear 350 2X4 a week or so back in non running condition, apparently they said it needed a new carburetor or a battery, I cleaned the carburetor thoroughly and got it running on idle and without choke now and it shifts into all the gears even into reverse. Aside from making me bounce a little when trying to start out with a bit of throttle the shock suffice to say needs work. Anyways I made a video of it running and would like your opinions on it, as to how it sounds while running. It seems like it has a little whine I'm not sure why that is maybe someone can tell me what it is. Anyways here is the video.
       
    • By Admin
      View File 1987 - 89 Yamaha Big Bear 350 Service Manual
      1987 - 89 Yamaha Big Bear 350 Service Manual
      Submitter Admin Submitted 12/13/2016 Category Yamaha ATV  
    • By Randel1
      Hello, 
      I have a 2004 Yamaha Bear Tracker in the shop for repair. I have the service manual but it doesn't have all the information I need to fix the problem. I need to know the voltage output of the stator charge coil and pulse or trigger coil at cranking speed. The wiring diagram color code doesn't seem to match and that is compounded by the fact that the wiring harness CDI connector is missing so I have 7 wires that need to be connected to the CDI. I can not find a circuit diagram of the CDI which tells me where the pulse/trigger coil connects or the charge coil connects. The other 3 wires (black ground, orange ignition coil, and r/b ignition kill sw) also need to be connected. The CDI has a single 8 pin connector and has a P/N 4XE-00 F8T19871 -1122 number on it and I believe it to be OEM. However I think the Stator and pulse coil are aftermarket items. I have resistance tested everything and it all seems to be in spec. but I don't want to miss wire anything and cause damage. Any help would be greatly appreciated. 
    • By Bruce Sawyer
      1987 YFM350FWTB 350 4x4 Big Bear when going uphill will sometimes act like the clutch realeases then re-engauge all at once.
      Seems to maybe be little more often if the engine is at about 1/2 throttle instead of at lower rpms.
      I have the Factory Service manual and checked the external clutch adjustment screw as ok and the H/L/reverse shifter lever linkage as adjusted correctly. It appears to be maybe a internal (inside the case) clutch issue or ??
      This is the type Big Bear that has the manual shift lever on the left front fender and has the manual foot shifter lever with 5 speeds forward.
      Can someone tell me how the primary and secondary clutch operates? 
      I assume one is mechanical and one is centrifugal. (what I'm asking is one clutch for the higher rpms and one for the lower rpms or ???. (the clutch appears to only momentarily release at the higher rpms is why I ask. The cycle has about 3000 miles of low speed through the brush hunting and has been well maintained, oil changed, etc and no deep water or mud useage.
      Anyone been into a similar issue with the big Bear ATV????
  • Similar Tagged Content

    • By Guythis448
      Looking for help on wiring up stock wiring harness specifically for a '88 Honda TRX 300 
      If anyone could drop a link or send me a PM it would be much appreciated 
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
    • By davidwestfall
      looking for direct shift shifting lever that properly fits my 2003 Yamaha warrior 350 and fits my foot the same as a stock 2003 Yamaha warrior 350 shifting lever fits my foot
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...