Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

D__L

2007 Suzuki Vinson 500 - Upgrades

Recommended Posts

I want to upgrade, not sure what size tires will fit and do I need wheel spacers and lift kit?

What performance mods do I need to do for the larger tires or don't need to ?

Like the Maxxis Vipr tires.

Maxxis Vipr front 27x9R-14

Maxxis Vipr Rear 27x11R-14

What size wheel will work? offset?

Stock 25x10-12 Rears and 25x8-12 Fronts

Stick with 12 inch wheels and get taller tires?

Thanks,

Share this post


Link to post
Share on other sites


You should be ok with your stock set up and need no lift ... things you could do later is exhaust and rejet carb or programmer if EFI, they go hand in hand, and maybe later a clutch kit ...

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By 2urb0liter
      Looking for front wheel assembly (hub, axle, rim, tire) for 1982 Honda ATC 110. 
      Let me know what you have and how much shipped to 58504. 
       
      Thanks!
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By shitboxlover
      I recently got a 250cc utility atv but it's way to slow. What performsnce mods can be done to it? It is the same as the loncin 250 desert storm but had some other chinese name
    • By Buell
      I have a 05 sportsman 700 carb and I also have tires and rims from an 19 Polaris General. Bolt pattern is the same. Do I need to change out the studs to be bigger?
  • Similar Tagged Content

    • By Alois Specht
      Hi there , have a KAZUMA 500 JAGUAR the rear diff is permanently locked , how can I get it out of lock just about tried everything I think, ?? .  Thank you your help is appreciated.
       
    • By mrfartsalot
      i have a 2001 suzuki quadmaster 500 4x4 that the primary cvt clutch is rusted on any ideas on how to get it off i want to try to reuse it if possible.
    • By Paul Maple
      I have a 1999 Sportsman  500, it was running fine, than started to lose power in the winter, I adjusted the idle screw and away I went, than a few weeks ago it died, I have found that i am flooding the engine, compression was at 70PSI and due to the compression release mech. i assume i am good as it compared to the same PSI on a 2000 sportsman 500 i have. i cannot start the atv unless i go full throttle and it starts an runs for about 30 sec than dies, again it is flooded. i ordered a new carb off ebay as i could get one for around $40. put that in same issue, i have checked the timing, (good), valves out of adjustment i adjusted to .006 still same issue, i have found the exhaust lobe and rocker arm to have some wear, i have ordered new ones, but am looking for any other input in this area as well. would the exhaust cam and rocker arm cause the engine to flood? i have used a bore scope and the piston liner has good cross hatching still? any input would be great.
    • By colin james
      View File 1996-2000 Polaris Sportsman 335/500 Service Manual
      This is the factory service manual for the polaris sportsman 335 & 500.
      You can download the section you need  or download all of the chapters for the complete manual 
      Submitter colin james Submitted 10/19/2018 Category Polaris ATV  
    • By colin james
      This is the factory service manual for the polaris sportsman 335 & 500.
      You can download the section you need  or download all of the chapters for the complete manual 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...