Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

2007-2009 Suzuki KingQuad LT-A450X Service Manual

   (0 reviews)

1 Screenshot

About This File

Suzuki KingQuad LT-A450X 2007-2009 Service Manual

  • Like 1
  • Thanks 1



User Feedback

You may only provide a review once you have downloaded the file.

There are no reviews to display.

  • Similar Tagged Content

    • By davefrombc
      1987-1998 Suzuki Quad Runner/King Quad 250/300 Service and Repair Manual
       
    • By davefrombc
      View File 1987-1998 Suzuki Quad Runner/King Quad 250/300 Service Manual
      1987-1998 Suzuki Quad Runner/King Quad 250/300 Service and Repair Manual
       
      Submitter davefrombc Submitted 01/28/2017 Category Suzuki ATV  
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By DUBLT
      Looking to purchase a windshield for my ATV, suggestions of what to buy with quality in mind and will fit without doing any modifications. 
    • By Ted Aregi
      I've got a king quad 750cc has anyone converted the fuel pump relay to a stronger fuel pump relay on there king quad?



×
×
  • Create New...