Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Mudding Around Stuck ATV

Ajmboy


Photo Information for Mudding Around Stuck ATV


Recommended Comments

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Add a comment...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Tagged Content

    • By Kristpj
      I know this tooic has been addressed by many, I’ve looked through many forums and pages. I did not find anything like the problem i have.
      I have a 2007 Kingquad 450. I have a new fully charged battery. When i turn the key, the dash flashes and seems to struggle before getting fully lite. We can hear a small relay near the computer clicking, i think it is the fuel pump relay. When i turn off the engine kill switch and press the starting button relays click and all the power shuts off, i turn the key off, engine kill switch then start over, power is there. Atv will start with pull start, but not elextricly. if i try to use my winch, all power cuts and engine dies. 
       
      Can anyone tell me what it may be? or has anyone fsced an issue like this before?
    • By Dee Wilson
      Hey there,
      The short of it: I'm getting a single click when I hit the start, and nothing else.
      The long: I'm a new owner to a 94 Timberwolf. I inherited it with the understanding that it needed a battery. It started without the battery when jumped, so I know it does work. I got the appropriate battery, charged it, and its reading 12.7V. Installed it, and all I'm getting is that click. Cleaned the carburetor today and reinstalled under someones advice, but still nothing. I'm gonna take the battery in to autozone to get it checked, and I was going to head to the spark plug next. But like I say, I'm new to this. Thanks for any and all advice.
    • By Don Colburn
      i bought a set of rims and tires off a 450 kodiak IRS its a 2013 factory rims and front rims are striking the calipers on my 2017 kodiak 450 anyone have any insight ,i thought they would just bolt on
    • By Zacharia Maisonneuve
      i have a 1993 timberwolf yamaha and the compression is good and lights work but for some reason the electricity is not going to the spark plug(s)! i got a friend to check it out and they said its no use but im not giving up! please help with this!
    • By chuckufarlie
      I have a 2018 Kodiak 450 EPS that just this past Sunday I ran through a bit of water.
      After the puddle the belt was slipping, so I pulled over and drained the ultramatic housing and the slipping problem went away. This was all in L and everything seemed to work fine. Later when I got on a road, I put it in H, but it still rode like it was in low... i.e. I had to rev it up a lot just to get to 30mph.
      When at home I pulled the ultramatic cover off to inspect, and it looked okay in there. Not much dirt, belt and everything are clean, but when I rev up the engine (with cage in place, of course), the belt doesn't get to the top of the clutch (maxes out about an inch or 1.5" from top of clutch, so maybe it is normal).. I put it back together but same thing... H seems like L still.
      Do you think the clutch needs to be further dissected for cleaning, or could this be an issue with the gear selector?
       
  • Check these out!




×
×
  • Create New...