Quantcast
Jump to content

mwilliamson

Members
  • Posts

    20
  • Joined

  • Last visited

Posts posted by mwilliamson

  1. Thanks for the idea. I just got married and went on a honeymoon so havent had much free time to check this out. Back to the real world now lol.

    Changing the jets or needles have not helped or hurt the problem one little bit. did not change it one little bit. i have switched back and forth a million times and have a hadful of jets. Heard a idea from a mech i know, how about the stator? i heard a rumor that they are hard to test accuratly but did test it and showed resistance at .8 book says .45 to .65 is good.

  2. The air box lid is not modified and it is on and they are sync'd. The way I understood it is that pilot would only help in the idle to 1/4 throttle range. It stumbles the worst at about 3/4 to full. Stumbles a little less but sill bad at about 1/2 to 3/4. And it runs great before i hit about 3000 rmp +/- at any throttle position. But I would try it if you still think that might be the issue. It is hard to explain exactly what is going on so i am trying to be clear. I thank you guys again for you thoughts and am going to pull the carbs back off and check in regularly to see what you think.

    I forgot to ask which way with the pilot.

  3. I changed the mains twice, adjusted the needle, inspected the choke, and checked for leaks. I did not change the pilot yet because the only way i can get it to climb in rpm is with a small amount of throttle but will try anything at this point!! For some reason the carbs are supposed to be jetted that way ( can't remember why). I am not familiar with float bowl vents but again will try! oh and the things i did try have not changed it at all

    Thanks for your suggestions my fiance really wants to ride. We both appreciate any thoughts!!!!!

  4. I posted a question last fall to try a figure out why my '05 raptor 660 runs so poorly after a local shop worked on it. They insalled the jet kit and cdi. It starts cutting out past about 3000 rpm. It feels like it is starving for fuel. Does not cut out at exactly the same rpm but close. If you play with the throttle (ease into it back and forth a little) it will eventually rev up but still cuts out when you hammer it!! This only happens when riding it... in neutral it revs straight to govener with no hesitation.

    ADD ONS

    gytr jet kit

    k&n filter

    D&G exhaust(slip on)

    CDI box (Ricks motorsports hot shot)

    THINGS I HAVE TRIED

    replace cdi box

    new jets- stock runs 140 & 145, shop installed 145 & 150, I installed 150 & 155 (dual carbs)

    Adjusted air fuel mix a thousand times!!!

    removed parking brake saftey switch

    tested coil

    THEN I GAVE UP!!! SO DID ALMOST ALL THE SHOPS IN TOWN!!!!

  5. Well the new cdi didnt fix it, still cuts out around 5 or 6 grand. I noticed it sputters a little while accelerating too. Im going to check the timing. How about the valves? Clearence off, bent valve, etc.??

    Or does anyone think the shop jetted it wrong? I have not ever jetted before, my lack of time and experience was why they did it in the first place. Or should i just take it to a shop and save myself the hassel??

  6. MWilliamson, welcome to the site. As my just explained we love Rabbit Valley and always been curios about the trails we see just north of 70. Do you ever come to our side of the divide?

    Every once and a while. We (my girlfriend and i) have never been over their to ride. Didnt know of anywhere to go that was good. But we were wanting to make a few trips out of town this summer (little sahara and white wash dunes ut. and maybe a trip to wy. )

    Their is quite a bit of riding around here so its hard to Justify leaving but we like different terrain . Is there some good riding that way?

  7. ive always ran 91 in my dirt bike and 4 wheeler even in the sand dunes which i hear is harder on motors because more throttle is used. Im not a mechanic whatsoever but 91 or 93 should be ok.

    any one else feel free to disagree though, wont hurt my feelings lol

  8. I have a real good feeling that the cdi is the problem. I actually got the manufacturer

    (ricks motosport elec.) to warranty it by going around the dealer in town and the supplier they got it from and contacting them direct. They where real nice and understanding. I will see in about a week if that will fix the problem.

    Thanks for everyones input and help with this issue!!!!!!

  9. Thanks !! Yeah rabbit valley is some fun riding!! Just north of the interstate in Grand Junction is all blm land and their is endless amounts of riding. Skinny ridge is out their. ( a few you tube videos ) Its all desert with rolling hills and a billion trails that all connect. Their is two easy to find acesses from junction and it is worth a try. 29rd. and patterson and 27 1/4 rd. just west of the airport. Its worth a try next time you come through. let me know im five minutes from 29 rd.

  10. Thank you guys so much!!! The pipe was installed before the rest of the work was done. The filter, cdi, and rejet were done by the shop so I would hope that it was done in right order. I will check the timing then go to the box. Any suggestions on a good cdi box because i suspect that it will not warrantied with it being six months old. And of course i left the old cdi with the shop.

    Thanks again!!!

  11. I have an '05 raptor 660 purchased a year ago that my girl rides. Over the winter i had a yamaha dealer install a gytr jet kit, cdi box. I also installed a k&n filter, and d&g exahaust all around the same time.

    Now it seems that when i hit around 5 grand the rev limiter kicks in??? sounds like it? The box does not have and adjustible rev limit.

    It has great power up until it starts cutting out. I pulled the spark plug, looks normal, replaced it anyways. Filter is clean. Don't know where to go from here!!!!!! It didn't do this before the "upgrades".

    ANY IDEAS ?????

×
×
  • Create New...