Search the Community
Showing results for tags ' water'.
-
I purchased the seals for water pump.finally got old one out and noticed shaft bearing are pretty loose.i see the clip on outer side of case against outer bearing.shaft will move towards inside a little ways then stops.how does shaft and bearings an oil seal come out. I cant find much help in manual 1994 bayou 400 4x4 KLF 400B
-
85 sx 250 ..been out twice and each time got water in diff.Diff is snorkled..would bad dust seals cause a leak into diff? Thanks
-
[ame] [/ame]
-
Hello everyone im new here and I have a problem with my 2004 yamaha kodiak 450. Yestarday my friend and I were riding in the creek and it is a slant where my front rack is under water but my exhaust is a couple inches out of the water and it starts sputtering when I go in reverse and cuts off. It won't crank back and my friend pulls me out.we check air box and it is a little wet but not much. I have it snorkeled by the way. And today I try to crank it again and still won't start please help! Thanks
-
I am in need of a water pump shaft for a 1996 Kawasaki Bayou 400 KLF400-B4. The part number is 13107-1287. Both the impeller and the water pump shaft are stripped of threads. Any help will be appreciated. Thank you. Please email me at [email protected] if you have any leads.
-
:surfing:[ame= ] [/ame]Suzuki Lt160 and Eiger 400
-
I saw in past threads or possibly from another ATV site when I Googled my shifter problem. I am in the NE Mountains and it gets cold. I have my 2012 Grizzly 700 in the garage and it is NOT heated. The cold weather here was about -5 to -15 F. When it got that cold my Grizzly 700 would not shift into any gear. Once it warmed up it did shift into gear(s) no problem. I saw this happen about 3 times already since I just got it about 3 weeks ago. I saw a thread in from the past saying to drain the shifter, that there is a hose with a plug? Where is this hose and plug exactly? How do I get to it? Again, like I said I am new all around (wet behind the ears) but I am a hands on guy. I really do not want to take things apart I don't have to. I really need specifics and/or a drawing. I don't think it is the adjustment as when it is not so cold say around 40 degrees F. It does not happen. Plus like I said once it warms up it is fine. THANKS!
-
I am replacing the seals on the water pump . I notice between the oil and mechanical seal there is a fine grits of sand that entered the weep hole . Some are putting fitting in the weep hole and route an hose to the handle bars and problem solve .On a mud pro the weep hole is close to the edge of water pump no room to install a fitting so my question is : if that mod was done with success by someone ,I would like to know what kind of fitting that was used. Thanks Alain
-
What's up I just picked up a 98 bigbear I'm lookin to build a snorkel and try to make it as water proof as possible.. That being said I'm just curios if anyone has one that's done this or tryed this before.. Just trying to find out if anyone knows where all the breathers are like crank and maybe diffs.. If someone could help me out that'd be great just trying to hit some deep holes with out filling my motor.. Thanks alot
-
ok i have taken the clutch cover off and got the water pump out the metal seal that is in the case were the impeller shafts goes how do you get that out i guess its part of the mecanical seal that is pressed in the case how do you get that out
-
changing stator in a 94 bayou 400.the oil is milky ,mixed with water.I am replacing water pump seals.how much oil ( if any) should be in this side of engine. there has been ( to me ) a lot of condination from vent tube lately. don't think head gasket is bad it was running ok when it was running. what do you think..
-
anybody near south mississippi that wants to go riding msg me, we putting a crew together now to hit the trails, going to be riding just south of interstate 10, if you are interested be forewarned that you will need your quads set up for deep water and mud, i will be bringing 06 honda rancher 2wd snorkled an sitting on 27 inch gators, and an 05 suzuki king quad 700 4x4 also snorkled and sitting on 28 inch mudlite
-
Hi, I am new to this forum and also new to “ATV”. I just bought 1998 Arctic Cat 454 4x4; according to last owner it wasn’t used for last 3 years. I tried to change the engine oil, noticed coolant water inside and mixed with oil. Now I changed the oil and filter and still can’t start. Any ideas? How fix this water and oil mix issue? Thanks
-
Was wondering if the newer housings on the yfz where the radiator hose goes below the exhuast will fit on my 2004. Was wanting to get the hose away from the pipe. Thanks .
-
This video was submitted to the QUADCRAZY Video section by Mats. Description of Video: Video Tags: http://www.quadcrazy.com/video/video/&v=122400855125
-
This video was submitted to the QUADCRAZY Video section by Mats. Description of Video: Video Tags: Very wet http://www.quadcrazy.com/video/video/&v=122340718343
-
This video was submitted to the QUADCRAZY Video section by CrazyEddy. Description of Video: snowmobile crossing open water Video Tags: snowmobile water http://www.quadcrazy.com/video/video/&v=117544693317
-
Is there anyway you can check to see if your water pump is working on a YFZ450
-
Does anyone know what the normal water temp should be on a Banshee?