Quantcast
Jump to content

2000 KLF300 BAYOU 2x4 Shifting straight past neutral into reverse without using reverse lever.

Quadman11

By Quadman11
in Kawasaki ATV Forum

 Share

Recommended Posts

Quadman11 Newbie

Quadman11

Posted
Posted

Hi Guys, First post. 

 

I'm Having an issue with my KLF300 2X4.

Just purchased a 2000 model KLF300, when i first rode is i noticed the gear shifting from reverse to first and vice versa was extremely hard and stiff. 

Now When the bike is running it is Shifting straight past neutral into reverse without using reverse lever, making neutral impossible to find. Also the neutral light and revese light has stopped working. To get the bike started i grounded the green wire coming from the switch so now i can start it again but the shifting issue is still there. 

I have adjusted the reverse lever and cable so that it is fully retracting but this hasn't changed anything.

 

Can anyone recommend anything to check etc? 

 

Thank you.  

  • 5 months later...
johnboyS81 Newbie

johnboyS81

Posted
Posted

sounds like its something internal possibly if you adjusted everything the way it should be done. my foreman with the red button on handle bars done the same thing accept lights still work properly.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Forum Topics

    • Cj Winds
      2009 Honda Rancher TRX420FA with shifting problems
      By Cj Winds
      I have a 2009 Honda Rancher TRX420FA with shifting problems.
      Usually it shifts ok when cold but after couple minutes it will stop shifting with no codes.
      The 1st shift clutch oil pressure when in first gear is 74psi. The 2nd shift clutch oil pressure when in second gear is 74psi.
      The 1st shift clutch oil pressure when in neutral is zero. The problem is when the tranny is in neutral the 2nd shift clutch pressure starts around 10-15psi and builds to 20psi. Is this normal?
    • OldATVowner
      99 Bear tracker no neutral or reverse light or start button
      By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • Dsluder
      Fuel issue
      By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • cruteg8
      Bell Crank Orentation 2000 Polaris Scrambler 400 2x4
      By cruteg8
      Does anyone know  the orientation of the bell crank for scrambler 400 2x4 it was not hooked up when I bought quad the way  i put it high goes into reverse and vise versa I flipped it 180 but that put  the shift rod at big angle and it just kinda grinds into gears so dnt think that is right either pretty sure it has to be the exact orientation and the rod adjusted accordingly but I cant seem to find it anyone knows please help 
    • Mikey509
      First time quad owner looking for advice!
      By Mikey509
      Hi guys, I was given a 2000 Honda Recon fourtrax 250 (I think that's the full name lol). The previous owner had it sitting for a while before I got it. It sat for another few years in my ownership. I got it up and going on its first test drive today!! I was wondering where everyone buys their parts from?  Coming from the car community, we have sites like RockAuto and many more. Anything like that for quads? Also would like to be pointed in a direction, if possible, for plastics. I am missing a few and would like to have it complete. I appreciate any input!

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...