Quantcast
Jump to content

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • By Trent Finnessey
      I’ve got a 2000 400ex with a dg slip on muffler, it came with he stock muffler on it but the previous owner had the dg in a box so I put it on. I’ve been riding it for the past month and a half and every time I let off it backfires, and the other day the backfires got way louder, 2x louder! I’m concerned that I may hurt my motor? Why does is backfire??? Thanks
    • By Dumass
      My name says it all. I have a '03 Honda Sporttrax 400EX with a new aftermarket carb on it that seems to be having issues. I can start it but it idles really rough and when I give it throttle it just kills the engine. I have tried adjusting the idle screw but to no avail. I am in the San Diego Ca area. 
      Any advice will be greatly appreciated. I would also like to get an owners manual for the thing too but can't seem to find a downloadable one.
    • By Arizona
      I recently bought a 87 TRX 250 not running of course, the owner had a brand new Key Switch on it.
      I think it is the wrong one or wrong wire colors as the colors dont match up with wiring diagram i downloaded for it. 
      anyone have a pic of their ign switch wires where they connect with the wire colors for that model? I ended up leaving the black/w stripe and
      green wire disconnected in order to hot wire it for other testing but would like to know as the colors dont match diagram. 


×
×
  • Create New...