Quantcast
Jump to content

Recommended Posts

Posted

I have a 1998 300 fourtrax that I have owned since it was new. It has done its fair share of sitting over the past few years but I have started and used it atleast 4 to 5 times a year and sometimes pretty hard around deer season. For the last few years it has had a skip or hiccup when running at half to full throttle (steady throttle). This thing has always started perfect, idles perfect and takes gas great, runs great except for this hiccup when holding it at a steady throttle under load. Sitting you can hold the throttle all you want and it purrs like a kitten. I have done the complete tune up, cleaned the gas tank, replaced a broken choke cable where it screws into the carb, took the carb off and it looks extremely clean, blew out the vent lines. I have also ran it with the gas cap off and I believe it runs better (hiccups less often) with it off then with it on. I have ran seafoam through it. Done about all I know to do except take the jets out of the card and clean them. Like I said the carb looks clean with no varnish buildup of any kind in it.

Any ideas would be helpful.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • By Suzukiquad
      Hi, I have been around everything with a motor since I was little, and finally purchased more to get my husband, and kids involved. I have 4 quads I will be searching around for information on. I have two 2002 Suzuki LT80K quads, a 1997 Yamaha Timberwolf 250, and a 1996 Kawasaki Bayou 220. I have had different ones throughout the years, and plan on buying another Yamaha Banshee. I plan on trying to learn more about all of them, so I can customize some of them. I know nothing about them besides how to race them, my dad always took care of the rest, but figured it was time for me to learn. 
    • By Memphis
      Not sure if in right place but here goes
      My 300 is lacking power only reaching 30mph and struggling uphill everything else seems ok other that this problem cleaned all fuel new filter pan and all new fuel pump and spark plug full oil change is there anything I am missing
      ps It is auto and does noy seem to want to get in another gear 5200 rpm at 30mph
       
      Regards
    • By ATVNetwork
      As the 2025 ATV Motocross National Championship Series (ATVMX), an AMA National Championship, got underway with back-to-back Florida AMA Pro only events, it was evident that Phoenix Racing Yamaha’s Joel Hetrick picked up where he left off last season.View the full article
    • By beast6228
      I've been trying to piece this Lakota 300 back together, slowly. It's been a rabbit hole however. I replace one thing, then it leads to replacing other things. Anyway, When I got this thing I noticed that the hose coming off the camshaft cover wasn't attached to anything, it was just hanging loose. (It's literally just a foot long hose attached to nothing) I figured since it was venting the head it would be ok and I am sure it is.
      However, last night I was looking at the service manual and noticed that it mentioned that this atv has a crankcase breather tube as well. Mine does not have one, so I looked at Partzilla and looked at the parts diagram and sure enough, it's definitely supposed to have one. The problem however is, the service manual does not show how it hooks up and the parts diagram only shows the exploded view of the assembly. I just find that kind of strange, nowhere in the manual does it show how it connects. Does it have it connector, attach to a nipple? It just doesn't say and it bothers me that there is a hole there without anything attached to it.  If anyone has a Bayou 300 or Lakota 300 with an intact breather vent system and could possibly take some clear photos of it or know how it connects I would be very grateful. I have searched high and low and cannot find any information on it.
       
      Thanks


×
×
  • Create New...