Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

upper_tanker

98? beartracker 250 question

Recommended Posts

Hey all, new guy here. I am wondering if anyone has one of these machines, that can possibly take a picture/tell me where the hoes goes from the timing chain cover. I took this machine apart in the fall of 2014, planning to rebuild the top end, and didn't get around to doing it until about a month ago. motor is back together, and I'm just curious as to where this hose goes. One end has a plastic ribbed fitting in it.

Also, the rear upper nipple on the carburetor.....what goes there? is that just a breather also or?

I have the rubber piece that slides into the rear of the gas tank with 3 hoses: 2 go to the rear, and 1 is just a clear piece of hose that isn't connected anywhere.

I have another one of these machines, but it is 5 hours away.

I guess that's what I get for waiting a year and a half to put it back together lol.

Thanks

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dwight Williams
      Ok, so I bought a 2006 bayou 250 for 200 bucks, kid couldn't start it and had no idea why it wouldn't run, I pulled the rope and felt what I thought was valve to piston contact, he wanted 500 and I talked him down to 200 and brought it home.  Sure enough, timing was way far out, timing chain incredibly loose.  So for fun I re-tensioned the timing chain and re timed it, got about 120lbs of compression, pretty low.  I cannot get the chain very tight but the the tensioner seems to work fine, the chain guides don't look very worn.  Also, when I took the head off the valves don't look bent and the piston has no discernible marks on it.  Is this an interference engine?  I sure thought I felt some contact with the pull rope but maybe no permanent damage was done?  Anyway, I plan on doing a full top end job as well as timing chain tensioners and hopefully that'll cure it.  Is there any reason other than chain stretch (I measured it and it's ok) or guide wear that would cause the chain to be so loose?  Thanks!
       
    • By marek porowski
      Good morning everybody 
      I’ll be looking to get a cover for my Polaris sportsman touring that can be used while I take my atv to the lake for ice fishing. 
      min using an open flat trailer and 
      I want to protect it from the road salt 
      I know Polaris makes a nice cover but it’s kind of on the expensive side. I’ve seen some covers on amazon and eBay but was wondering if anybody has any suggestions 
      Thanks 
    • By Daniel Gibson
      Working on a bayou 220 that has been ran extremely hard it's whole life. Literally had almost an inch thick dirt/oil covering the motor. Yeah that bad. Surprisingly it runs though. I cleaned the carb and tank multiple times. They're clean enough to eat off of. Readjusted valve lash and set timing. Was about 3 teeth off. It cranks good and runs good only problem is I have to cover the carb intake basically choking the hell out of it for it to start. The com choke works fine. It does this each time I start it regardless of temperature both ambient or motor. Wth? Compression is at 115psi I get 130s if I put a little oil in the piston chamber. Please help. Thanks 
    • By Jun Dela Merced
      NEW HERE IM NEEDING SERVICE MANUAL FOR 2014 CAN AM OUTLANDER XMR 1000
       

    • By Frank Angerano
      I’ve decided to post  a thread on the process of cleaning a carburetor and what’s needed in order to do it properly.    There are some members that are new to this and are not very versed in doing so. I want to help and feel this might explain things better. I would hope this helps you along.     We all have our own little tricks of the trade so I’m sharing my process on how i break a carburetor down, clean, reassemble and adjust it to peak performance. I welcome any other members input on this topic.     List of things I use:   Safety glasses !!!   Rags.   I like to use old white Tee shirts or I buy and always have a few white pillow cases from the dollar store on hand. The cheap ones.     I like to use a frisbee turned      upside down like a bowl to keep the liquids to a minimum on spillage to the work bench.    A set of cleaning picks and brushes or a piece of bicycle break cable, I separate the strands and use them to clean out the tiny holes in the jets. (Pic attached)     A can of gum out  carburetor cleaner with the small red tube that attaches to the spray tip.  (Pic attached)   A can of compressed air, the kind used to clean out keyboards on computers. It also has the small red tube that attaches to the spray tip.  Or a compressor if you have one with a blow out tip.  (Pic attached)   A piece of clean hose that I can connect to the fuel line port on the carburetor to test the float operation. About 10 inches long.    A few Q tips.   The process: I like to put the pillow case down on the work bench and spread it out flat.   This really helps in being able to keep track of parts. Especially because it’s white.     I use the frisbee because it’s small enough to keep parts contained and durable enough to deal with the chemicals and any gas that will come out of the carburetor while opening it up.     It’s important to make sure you keep track of where everything came off and where the screws and parts all go back.     I like to start at the bottom and pull the bowl off. I immediately spray the inside of the bowl down with carb cleaner until its about half way full and set it aside.   Then I take the float out and check it for any fluid inside. If it’s a white color float you can hold a flashlight under it and see through it for any fluid inside.  If it black just shake it up and listen for fluid inside. No fluid inside is a good thing !    When the float comes out the fill valve needle will come with it. I take that needle and put it in the carburetor bowl that I filled with carburetor cleaner. This way it soaks for a bit. I do the same thing with the jets also once they are unscrewed and out toss them into the bowl to soak.    Take the air/fuel mixture screw out and soak that as well.  Side note: the air/fuel screw should have a screw, spring, washer and o ring.    After all the jets and parts are out and soaking I like to take the carburetor cleaner, use the small red tube and stick it in all the little holes/ports on the carburetor and spray.   I do this while it’s in the frisbee. This way there is no mess. I look to see where the spray pressure comes out on the other side of that port.   Once this is all done I start running my brushes and cleaning tips gently through all of the holes/ports and spraying it again with the carb cleaner.  After I feel I’ve seen a clear flow of fluid through all the openings I spray them with the can of air the exact way I did with the carburetor cleaner. This will blow out any left over junk that’s still in the carburetor.   Check the choke operation is working properly and spray it clean. Most choke devices are easily cleaned up so hit it and move on since they are mechanical and it’s just a matter of freeing them up, spraying with cleaner and lube.   There are multiple types of chokes but many of them for the most part are mechanically operated.    Once this is completed I wipe the entire carburetor down good and blow it clean and set aside.     I then start working on the jets one by one. Start by running the cleaning tips and brushes through all the tiny holes making sure they are all clean. Hit it with the carburetor cleaner and then air. I hold a flashlight to it when it’s done so I can make sure all of the holes are clear. I set all the jets aside on the work area.  Do the same thing for the float needle and air/fuel screw.    Now once this is all complete you can set the frisbee aside and start to reassemble the carburetor on the clean white surface.   I start by running a Q tip in where the fill needle sits into the carburetor. Some carbs have a small o ring that needs to be clean for proper seating of the fill needle.     Carefully reinstall the jets where they came from and do not strip or over tighten the jets and use the proper size screwdrivers when removing and reinstalling the jets.    Reinstall the air/fuel mixture screw and set it to what’s called out in the manual for that bike.    Install the float and fill needle assembly.    Now in order to test that float I like to take that piece of hose I mentioned and connect it to where the fuel line gets connected to the carburetor. I then turn the carburetor over to the upright position and blow into the hose. You should hear air coming out of the bottom of the carburetor. While blowing, lift the float up and the air should stop.  Let it go and the float should fall down opening the fill valve and you should hear air again.  The air should stop about 3/4 way up when raising that float while your blowing air into it.   If so then your good to go. If not make an adjustment    Set the carburetor down, take the bowl and empty it.   Clean it out and scrape/wipe any old junk inside and blow it out good.   There is a screw on the outside of the bottom of the bowl. Remove it and clean it out and reinstall.     Turn the carburetor over and reinstall the bowl. Tighten the screws in a crisscross pattern so the bowl seats evenly.     I like to put the hose on one more time and do a float test to make sure it’s opening and closing properly. All you have to do is blow into the hose and run the carburetor  upside down to see if the air stops.     Reinstall the carb and you should be good to go!    All pics of the items I use are attached below.   If you understand this great. If not ask away! Don’t be shy and don’t cut corners.   You will only wind up pulling the carburetor off of the bike for the third and forth time before you get it right.    The last thing to be discussed is dialing in the air/fuel screw when your finally put back together and running.  This is a relatively easy task.   Again I hope this helps!    Frank.     


  • Similar Tagged Content

    • By BosoxBruce
      Recently I noticed gas leaking from under the gas tank on my 2005 250 2x4. As I looked closer it appears to be leaking from the shut off valve under the tank. It's the valve with the handle that can be turned to open, close or reserve. Can this part be replaced? Thank you.
    • By Derick Joel Smith Trimmings
      Buying a Baja 250 tomorrow for 600 bucks, needs nothing but a wheel bearing, i already know Baja is an off brand crappier. Manufacturer, but does anyone have any tips or knowledge of these bikes? 
    • By fatfarmboy
      Just bought (Tue. evening) an '89 Suzuki 250 4wd that has been sitting out the last 5 yrs. It's complete, including the shift knobs, battery cover, and headlights. It has the optional cooling fan on it (probly stuck - didn't check), and the engine isn't locked up. Plastic looks good and isnt cracked. Racks aren't bent up. Shift lever works, the foot brake moves (needs oil - have to pull it up by hand), and there's black oil and no water in the engine sight glass. Guy was asking $125 and gladly took $100 for it. Anxious to get started on bringing it back to life. Been wanting one of these for years. As soon as I can get to it (working on a junky "Jackel" right now - Chinese Yamaha Timberwolf). I'm going to pull the tank off it and clean it, clean & possibly rebuild carb, put in new plug, and a battery, then see what happens. If nothing, will keep going until it runs. Feel free to respond if you want to, I'm mainly just excited and wanted to tell somebody. 
    • By Flanstone
      I just bought two 1985 TRX250's from my father-in-law. One runs great, the other not so much. The one is having issues with the shifter. The shifter seems to be resting lower than normal. When I press the shifter downward, it just pops back up. Any thougjts as to what the issue might be?
    • By Christopher Williams
      Hello all, 
      i just rebuilt the top end of a 99 Bear Tracker 250 and it can’t get it to hit off of gasoline or starter fluid. Occasionally it will backfire. Right now I’m just trying to get it to fire off without the carburetor like I’ve done a thousand times before with other engines. Usually there is no response, but occasionally I get a backfire through the intake. ISeems like it’s out of time, but I don’t see how that could be possible. 
      Here’s what I know:
      1. compression 120psi
      2. all timing marks are lined up after numerous revolutions. 
      3. Strong spark. 
      4. Valves adjusted correctly. 
      Thanks in advance. 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...