Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Newowner

Kazuma Falcon 150cc Chain Tensioner Spring

Recommended Posts

Could anyone post a diagram or picture showing how the chain tensioner spring on the quad. Got the quad a few weeks ago and the spring has come looses and unsure how it should look. Thanks

Share this post


Link to post
Share on other sites


Yes, but the clip doesn't show the chain tension spring. Hoping that someone could maybe take a side on picture of the spring in it's normal position. Thanks.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By bradken19
      the king quad had sit for about 1 1/2 years. So I rebuilt the carb and now it will not start. Any help will be greatly appreciated.
    • By Brittany Jones
      Yes I just got a 1998 polaris xplorer 400 4x4. Ran fine after hauling then died. Cleaned carb and put new fuel filter, hose, and new battery in. Starts 3 out of 10 times but will only run for a short time. Any suggestions?
    • By kgrant
      Fixing up a 1998 King Quad 300. The rear brake was locked up, and the owner tried to force it free and snapped the axle.
       
      I disconnected the brake cable, and tapped on the backing plate with a soft mallet to get the brake freed up. When I pulled off the brake drum a bunch of nasty rust water came out.
       
      Once I had the axle out, I popped the boot off so I could see the inner u joint so I could phase/synchronize it with the outer. There was a flat steel disc floating around in the boot, looks like it used to be pressed into the end of the axle. Glad I got that out of there before it munched up the joint.
       
      The book says the yokes should be aligned, I couldn't get mine aligned. They were always 7 degrees off from each other. A bit frustrating, maybe that's within the tolerance limits?
       
      But I got it all back together and it runs great.
       




       
       
    • By Mudrecon
      Haven't got a service manual for this yet so I'm flying by the seat of my pants I made myself a shifter extension to go up by the gas tank took my foot shifter off to weld it and now when I put it back on I don't seem to be able to find neutral. Is there some asinine reason that you have to do something internally when you change or remove the foot shifter? It was a simple take off weld put back on and dog bite my pecker it's not working. I hope this is something simple I've done and that's something I need brain surgery for. Cheers fellas I know y'all will have the right answers
    • By JacobSlabach
      I have a gentleman that asked me to service his bayou for him.  I have always wondered what oil should be used in atv engines?  Pros?  Cons?  What weight should be used in what type of weather?  Is there one kind that I could bulk buy and safely used in any quad I worked on or owned?  What about performance?  Engine Life?  This has always been a 🤔🤔🤔 area for me with quads as far as why you would use one type of oil over another....
      Thanks!
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...