Quantcast
Jump to content


Need Help 1995 Polaris 400 Xplorer

TPW

By TPW
in Polaris ATV Forum

 Share

Recommended Posts

TPW Newbie

TPW

Posted
Posted (edited)

I'm trying to get a basket case Polaris 400 started. The motor was locked up when I got it and it is now free and turning smoothly and no apparent damaged to piston sleeve, I rebuilt the carb and put fresh gas actually used premixed 50:1 fuel. Has good spark and 70 lbs of compression. Can't get it to do much more than an occasional bark from the engine. Any "next steps you could recommend would be appreciated.

Edited by TPW
typo
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • semicolon
      TRX350D fuel pump problem
      By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • Clydaho
      2022 Hisun Sector 550 Gas gauge stopped working
      By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • rgeiser
      2003 Polaris Ranger 400-500 Service Manual
      By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • ResQ91
      Help with 1987 Yamaha Big Bear YFM350FWT Carb
      By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • Its-always-something
      98 arctic cat 300 2x4 hi rev choke when started
      By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...