06 outlander 400 missing fuel after half throttle
-
Similar Forum Topics
-
By semicolon
Hi, I am having issues with my TRX350D fuel pump. It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals. I have fitted a new pump, fuel cut-off relay and rectifier. Still nothing!! The pump runs when attached to a battery. The engine will start on the choke and the filter fills with fuel but it will not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine. Any ideas where to go from here would be very much appreciated!!
-
By BenJammin
I did a compression test on my 2005 Bombardier Traxter 650 CVT and it's 75 PSI. service manual only talks about leak down test. No specification for engine compression the manual. What does 75 PSI tell me? Thank in advance.
A little history of this machine. 640 miles. Picked it up about 2 years ago, not running. Probably the computer. Tested all circuits and confirm it was the computer. Long story short, I watched a Youtube video and fixed the computer. ATV now started and runs. BUT, it tops out 20 MPH. I cleaned the carb 3 times also using a Mikuni carb kit after the second time. Slide in carb is going up and down. Only adjustment for fuel is at 1.5 turns out. NGK Sparkplug had soot on main part but brown on the electrode. Champion sparkplug is brown. I check CVT clutches and they both appear to engage like they suppose to. Checked valve clearance it's 0.00, I can't get any feeler gauges in-between. I check timing chain I believe it's in the correct position and hasn't skipped. I removed muffler plug and drilled into muffler to try and make sure it wasn't plugged.
-
By ResQ91
Hi Guys!
New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
I have an 87 Big Bear 350 YFM350FWT
The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
What would you recommend other than a carb rebuild?
Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
Or ??
Thanks in advance for any advice you have!!
Dave
-
By Gwbarm
I have been exploring all the options available, so many, its hard to choose. I have kind of narrowed it down to the Honda Pilot, Subaru Outback, and Kind of looking at the Outlander, although its a little small, the new one is nice looking. Just wondering if anyone has any recommendations or gripes with any of these rides. I have driven Jeeps for the past 25 years and they have been great, but their price point has gotten to high. Expieriences good or bad would be helpful. Thanks!
-
By DrtyGrlKristin
Just thought I'd start a new thread for newbies to the site!
If you're new here, tell us who you are, where you're from and what you ride!!!
Lets get to know each other a little better shall we?
I'm not new to the site, obviously, but...
I'm Kristin from Denver!!! I ride a 2008 Yamaha Rhino. She's my muddy baby!!!!!! Several aftermarket parts on her. She's good to me! We try and ride every weekend. This weekend we're off to MOAB! :woot:
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.