Quantcast
Jump to content

Suzuki King Quad 700 give it gas then it dies

Brent Wright

By Brent Wright
in Suzuki ATV Forum

 Share

Recommended Posts

  • Admin changed the title to Suzuki King Quad 700 give it gas then it dies
  • 4 weeks later...
meinsheizer Rookie

meinsheizer

Posted
Posted

Clean the carb, dump the fuel and replace with new, and change the fuel filter. It's most likely some water in your float bowl and will idle ok because it's only pulling small amounts in at idle but when you hit it it wants to suck up a lit of fuel but theres to much water so it dies.

  • 1 year later...
ITWarrior Rookie

ITWarrior

Posted
Posted

KQ 700s are EFI. It's likely the throttle position sensor that's faulty or out of adjustment, or a faulty fuel pump. You can see what the EPU thinks the TPS is doing by looking at the lines on the bottom of the dash when you turn it on with the diagnostic jumper wire in.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Zrach
      Faulty CDI Workaround / "Park-Circuit" Fix: 2009 Suzuki LT-A400 (KingQuad)
      By Zrach
      I wanted to share a successful workaround for a "no-spark" issue on a 2009 LT-A400.
      This is specifically for cases where the CDI has been diagnosed as faulty, but the age or condition of the machine makes the cost of a brand-new OEM unit hard to justify.
      Note: This modification compromises the factory “no-start” circuits.
      On some malfunctioning CDI units the internally damaged circuitry is only partial.
      Feeding full time power to the Parking Brake pin, the unit is triggered to bypass the internal fault and produce a healthy consistent output to the Ignition coil.
      The Modification
      See the second diagram attached below for the wiring specifics.
      The Result:
      The machine has clocked over 1,000km since this repair and is still running strong with no ignition dropouts.
      ⚠️ IMPORTANT SAFETY WARNING ⚠️
      Please be aware that this modification compromises the factory safety "no-start" circuits.
      The machine will now start in gear. The safety interlock involving the handbrake is no longer functional. The machine can move unexpectedly if the starter is pressed while in gear. Proceed at your own risk. If you sell the machine or let others ride it, ensure they are fully aware that these factory safety buffers have been removed.
      Faulty CDI Workaround.pdf
    • BillR94
      98 Polaris Magnum 425 4x4 speed limiter advice needed.
      By BillR94
      I suspect this bike may have a bad speed limiter. The part number for is 4060204. I found this one on ebay but it has a part number that is 1 number different. (4060203). It has the same LR44-2 and says its for a 94 Magnum 425. Will this one work on my machine or do I absolutely have to have the 4060204? Your advice would be appreciated. Thank you
      https://www.ebay.com/itm/326817022020?_skw=Polaris+speed+limiter+LR+44-2+4060204&itmmeta=01KF74RJDTYSQNAP11RNJHCRQQ&hash=item4c17d00044:g:IRYAAeSwfO1o7eFo&itmprp=enc%3AAQALAAABAO7PUuNWmJ%2B%2BUShgI9tQz%2Fp%2FPZwHFglDA7v--td9bxBP05QJN8jM6A97tWp7MfGdxP%2Fo9vRaFVpxhV0%2B86jsb4r1WPwXcF%2FLp132KMxBdyLCSwt%2FtSvxD4%2B2RhmZOKzQYHqX0tNsUT1cqqf1TT0TxauZTveHSqgA8UlZ3Qb3ALQlGIIFiaiXjpWNHwRUnyNGKvI5gDVtbwv7eIrkF8m42Bvb75n4dwn0jTJyLPLZveJMPDcjlyHha0wv1Q1JbVnF%2FxxfSi2ros0dbFHRLsBpdH0TT9LNoSTtump3ZDZ%2BA9xqfasfcwHrDJzDX2BDC9Jx8NZeI%2B3mcvOJ7H8qPpwW7OY%3D|tkp%3ABFBMhKfi5Plm
    • WeeBee
      Advice on ATV Trailer Brand?
      By WeeBee
      I'm looking at buying a New "CarryOn" 5'x8' Trailer with the Ramp Gate and Mesh Floor from my local Tractor Supply store ! Anyone have any experience with this Brand of trailer to share ?? Thanks!
    • GERONAMO308
      PLASTIC WELDING HINTS TIPS AND ADVICE WANTED
      By GERONAMO308
      Hi all, does anyone know what type of plastic is used for making ATV fairings.
      In particular Suzuki Quadrunner 1992, if i cannot get a plastic for it in Red for the rear i will attempt repair.
      I have a King Chrome plastic welding kit, however you need to know what type of plastic you are welding.
      Any advice would be greatly appreciated. 
    • Eisaks777
      bpr bombaradier rally 200 2007 a lot of gasoline in the oil sump 4 stroke, what is the problem and how to fix it
      By Eisaks777
      hello, i have bpr bombaradier rally 200 2007 which has a lot of gasoline in the oil sump, it is  4 stroke. Has anybody had problem like this and which can be the cause and how to fix it. i rode it today at -2 degrees celcius if it helps.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...