Quantcast
Jump to content

Recommended Posts

Posted

Ok guys, I am a glutton for punishment! I picked up this 01 2wd Rancher because the plastics looked good on the marketplace. It has been sitting in the guys back yard for 10 years. The original engine blew and they swapped in an electric shift 4x4 engine. 😒The engine is locked up and was full of water. The wiring is hacked where they tried to get it to run and the rear end needs new swingarm bearings where they left it laying on the ground in the woods for 10 years. Has anyone here ever did the engine swap? First thing is to straighten out the wiring and get the engine free to see if I can get it to crank over. I have swingarm bearings ordered and a new ignition switch. So hopefully I can at least roll it around soon. 🤣

IMG_20250207_161928912[1].jpg

IMG_20250207_162039911[1].jpg

IMG_20250207_161933066[1].jpg

IMG_20250207_161958327[1].jpg

IMG_20250207_161948205[1].jpg

Posted

I got the engine broke free and I am going to fill the crankcase to the top with gasoline and let it sit for a day and then drain it before putting oil in. I am struggling with a flare up of diverticulitis right now and can only work for short spurts.  Hopefully Monday I will get the swingarm installed and get the wiring straightened out and try to get spark and maybe a first start. 🙏

  • Like 1
  • 4 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Forum Topics

    • By Cj Winds
      I have a 2009 Honda Rancher TRX420FA with shifting problems.
      Usually it shifts ok when cold but after couple minutes it will stop shifting with no codes.
      The 1st shift clutch oil pressure when in first gear is 74psi. The 2nd shift clutch oil pressure when in second gear is 74psi.
      The 1st shift clutch oil pressure when in neutral is zero. The problem is when the tranny is in neutral the 2nd shift clutch pressure starts around 10-15psi and builds to 20psi. Is this normal?
    • By cruteg8
      I was thinking about trying to repair some cracks in the plastics of a Lakota Sport i just purchased has anyone ever tried (U.S. Chemical & Plastics USC GarageTM Flexible Glaze USC-77704 it) https://www.ebay.com/itm/364866165725. i was thinking jb weld for plastic then using this as a bondo that can be sanded smooth 
    • By 88classic
      I have (2) sets of brand new plastics available for Honda Rancher 420 2014-2023. These are genuine genuine OEM Honda plastics. One set is white and the other set is green. The boxes these are in are too big to ship.(Unless you want to pay for it. If so, lookup your own shipping rates from 17325 and box size is 58"x35"x18").  $400
       

       

    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By jeffrocdx
      I'm working on a 2002 Polaris Sportsman 400 with shift indicator problems. The indicator panel only will show Neutral and Reverse. If it's in High or Low, the indicator will show "R".
      I have replaced the three position indicator switch on the transmission. There is also a two position switch on the tranny that I didn't replace. If anyone is familiar with this problem, please let me know what I need to do. Any help is greatly appreciated!
×
×
  • Create New...