Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

Does anyone know how or what kinda of tool to use to ajust the pilot screw on a 94 250 suzuki quadrunner. It seems that you can't get anything between the carb and the motor. I belive it should be turned out 2 1/2 turns out is this correct? Thx

Sent from my SGH-T989 using Tapatalk 2

Share this post


Link to post
Share on other sites


The only way I know of is to remove the carb. Suzuki manual says 2-7/8 for a new pilot jet screw. I was mistakenly under the impression it was supposed to be 1-1/2 and that is what mine is set at(93-LT-4WD). It runs fine, so I'm not going to remove it to mess with it.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Tagged Content

    • By JunkerG
      I am unable to find the default mixture screw setting for this Mikuni BSR33 carb. The screw only unscrews 4 turns and does not unthread out of the carb, (no way to clean it). When I took the carb apart to clean it the screw was set at 1 turn out. I bought this unit when it was only a few months old from a friend so I know it is the original carb. I know most carbs are set at 2.5 turns out, but would like to find out what this specific carb should be set for.
    • By stillsmoken
      Just wondering if there was a trick to ajust the pilot screw lol. I have a 94 suzuki 250 quadrunner and you really can't get a screw driver inbetween the motor and carb.
      Sent from my SGH-T989 using Tapatalk 2
    • By FTPVic
      2001 AC 300 Green
      When seating the fuel mixture screw is it supposed to protrude slightly? I can see the tip sticking out. Im just wondering if what I think is seat is actually to far in. Should it be below the surface already when I begin backing out 2-2 1/4 reset?
    • By KCOLLIS
      Hi all,
      I have a 2007 king quad 450 with starting/idle/power problems. My two boys had a go at it while I was away at work and now I found that the idle air screw was removed and I don't know about setting it up. I want to set this before I start on the other problems. New fuel pump, new injector, new foam air filter, error code reads -C00. Any help would be appreciated.
  • Similar Topics

    • By AKMichael
      Hello All,
      I have a 1999 Yamaha Big Bear 350 4x4 trying to get fixed up so my grandson can go out in the woods with me.
      We have owned it over 10 years.  It got harder to start, until it finally would not.  Replaced the carb.  Right afterwards, it started and ran nicely, but after turning it off, would not restart.  Tonight I used starting fluid and ran, then died.  Adjusted the idle up a little, used more starting fluid and ran great.  It idled about 15 minutes.  Turned it off, and restarted.  Ran it around the yard about 5 minutes.  Turned it off, and would not restart.
      Any ideas or suggestions would be greatly appreciated!
      Thank you. 
    • By Abbeypalm
      While cruising, my 2011 750 king quad suddenly shut down. As it happened, red lights on the display flashed. Any ideas? My head lights suddenly stopped working about a week ago, if that helps. I have no power at all. Thanks 
    • By Brennon Heflin
      So I bought a 2000 quad runner 250. I'm having some issues an wondering what it could be I replaced the pet cock valve an the fuel filter an pump inside tank I also put a voltage regulator on it. The problem I'm having is that when u give it half or more throttle it bogs down an loses power what could it be the bike is almost like new an cant figure it out any help would be great
    • By smitht18
      Looking for the rectifier.  Most bikes have near magneto.  It appears the KQ has it in front.
      Can someone tell me exactly where it is? 
      Bike not charging and magneto checks out ok
    • By Hunter19
      How are you doing guys I just joined I have a 1998 Suzuki King quad I’m having problems with high RPMs the ATV idols perfectly but soon as a throttle up it doesn’t stall but it just bogs down it has no power any suggestions thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...