Quantcast
Jump to content

Kawasaki Lakota - Hard Shifting

dblbassdrumer

By dblbassdrumer
in Kawasaki ATV Forum

 Share

Recommended Posts

dblbassdrumer Apprentice

dblbassdrumer

Posted
Posted

ok i got a problem i put all new clutch plates in my lakota now when i went to put on the 4 blots (clutch basket)2 of them snapped and now i gotta really get into mega high rpms in order for it to shift and SOMETIMES i gotta stay on the gas while holding up,let off the gas and the level goes up NOW my question is could those 2 bolts have anything to do with the problem ? it never did this before

oxidized_black Grand Master

oxidized_black

Posted
Posted

hopefully ck1999_400ex will jump in here and give you some advice ... i think if i were you, i would tap those broken bolts out and replace them, only because that engine is turning out 5000+rpm and if it had 4 holding it in and only 2 now, i would be worried about losing something ... JMO

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Forum Topics

    • logray
      Looking for Quadrunner Flywheel Starter Clutch Gear race diameter
      By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

    • HoldenBoy
      Starter not staying engaged while cranking
      By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • jeffrocdx
      2002 Polaris 400 Sportsman Shift Indicator Issues
      By jeffrocdx
      I'm working on a 2002 Polaris Sportsman 400 with shift indicator problems. The indicator panel only will show Neutral and Reverse. If it's in High or Low, the indicator will show "R".
      I have replaced the three position indicator switch on the transmission. There is also a two position switch on the tranny that I didn't replace. If anyone is familiar with this problem, please let me know what I need to do. Any help is greatly appreciated!
    • quadnut20
      Clutch mods !!
      By quadnut20
      Just picked up a 2025 Yamaha Kodiak 700 fixing to do a EPI Clutch mod to it since I dropped bigger tires on it !! Air box , exhaust , and programmer next ! 

    • ButchM
      2023 Hisun Axis 700 fuel problem
      By ButchM
      Hisun 700 EFI. Replaced TMAP sensor had broken off . Fuel pump pressure 41psi. The only way I can keep it running (and runs fine) is to close off fuel return line. 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...