Quantcast
Jump to content


2004 kawasaki kfx400 help


Recommended Posts

Hey guys my first post on this forum, anyways i could use some help regarding ym atv, before i start just want to say last time i rode it was before winter and the starter was shot, but it still ran and started up.

So what i did:

I put the key in and tried to jump start her because theirs no starter, and it would go to start and then i would hit the gas and it wouldn't do anything and die almost immediately.

So i had my dad hook up a rope to his truck and tow me. The quad would "run" while being toed but i would pull in the clutch and it would die immediately. Pressing the gas also did absolutely nothing. So i was dumbfounded and did a routine tune up. I changed spark plug, oil, and cleaned carb best to my ability. Still wouldn't start. I noticed there was no neutral light on which i have a feeling that it could be the problem. So whats wrong with her :(

Also I had to changed my ignition because i lost my key, it was a simple unplug and plug back in kinda deal. I also changed clutch lever and wire. shes at a shop right now but i want to see if i can diagnose here by myself. so any ideas?

I also noticed when changing the spark plug that the spark plug cover and the wire that goes into it were disconnected when i changed the spark plug not while i was trying to start it. so im thinking since that tube was ripped out of the cover that could also be a problem with the spark to engine

Edited by danhouse18
forgot a detail
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By mehim
      Hi everyone. 
      Let me explain the thread title. 
      My husband and I are very active in the nudist community, and we have stayed at many and most of the mainstream nudist and clothing optional campgrounds in the USA. We are now approaching our retirement and would like to start a podcast to share those off the road / backwoods / little known camping areas where nudity is allowed. We have purchased a 5th wheel camping trailer with a rear garage for the ATV and now need some good reports on the one to buy. 
      We are most interested in a side by side unit but would love to get your thoughts. 
      Feel free to stop by and say Hi and ask anything you would like to better understand what we are looking for in an offroad unit. 
      Thanks for reading and hope to hear from you. 

    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By Charlesbrown
      I’m looking for a top end kit for a Yamaha. I would like to see how well the engine runs before spending $6-$7 hundred on oem. Niche has complete kits from $1-$2 hundred.  Anyone have experience with Niche or similar Chinese companies? 
    • By Admin
      Looking for Yamaha ATV VIN (Vehicle Identification Number) Number Decoders? Once you find your ATV VIN number off the tag on your Yamaha ATV, you can go to all kinds of websites that have VIN Decoders available. The best ones are backed by the Yamaha ATV manufacturer, however there are plenty of aftermarket Yamaha ATV VIN Decoder websites on the web. This topic will stay pinned and if you find any to add, please do it with a reply. 
      The following Yamaha ATV VIN Decoder websites are available where you can just enter your VIN number and it will shows you some of your ATV model details:
      CycleVin.com - Use Our Off-Road Vehicle Search to look up ATVs and more!
      KBB.com https://www.kbb.com/vehicle-history-report/
      CARFAX https://www.carfax.com
      autoDNA https://www.autodna.com
      VinAudit http://www.vinaudit.com/
      decodeTHIS https://www.decodethis.com
      VINCario https://vindecoder.eu/
      NICB Theft Check https://www.nicb.org/theft_and_fraud_awareness/vincheck 
×
×
  • Create New...