Quantcast
Jump to content

2000 Kawasaki Prarie 300 - Drive Train

brislette

By brislette
in Kawasaki ATV Forum

 Share

Recommended Posts

brislette Newbie

brislette

Posted
Posted (edited)

i have a kawasaki prarie 300 it is a 2000 when pulling bouncey hills i hear a ginding noise sounds like from the drive train and i have the throttle floored and it seems like i loose throttle. wont go no where. just put on a new drive clutch unit old one was worn. the rear end looks good on the splines on the drive shaft dont lool worn but the one end sticks i have to hit it with a hammer to get it off. i greased them thinking this would help it seemed to for a about 50 miles or so. can this binding be my problem or is it in the gear box or something

else. thanks for any help.

Edited by brislette
forgot to put in make and year

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • Shorty51
      2006 Arctic Cat Utility transmission drive shaft replacement.
      By Shorty51
      Good morning, I am new to the forum. I'm 75 years old and love getting ATVs back to usable condition. I particularly like the 2006-2009 Arctic Cat 250 Utility. I currently own 6. The 2006 I am working on only has reverse and low gear. The "drive shaft" in the transmission is completely stripped where the high gear would mesh. Has anyone on here replaced the shaft. I'm told I have to split the case. I was hoping that someone on here could let me know how hard it will be. I already have it stripped down to where the shaft coming in from the clutch side is the only thing left. I was hoping I could just remove the driven clutch and drive it out from there. Directions say different. Any help would be greatly appreciated.
    • marlon smith
      1990 Kawasaki Bayou 300 Intake and Exhaust Pop
      By marlon smith
      1990 kawasaki bayou 300c idles fine but pops out exhaust and intake when trying to excel, will not take throttle past 1/4 , any one had this problem?
      have replaced carb twice, same thing, fresh built engine cylinder head, same as before, new spark plug, flywheel key is good, pulser test good, good spark
    • quadnut20
      Clutch mods !!
      By quadnut20
      Just picked up a 2025 Yamaha Kodiak 700 fixing to do a EPI Clutch mod to it since I dropped bigger tires on it !! Air box , exhaust , and programmer next ! 

    • P_syko
      Shaft drive vs chain drive?
      By P_syko
      Which is more reliable? Shaft or chain drive? 
    • dkgg5755
      2003 Kawasaki bayou 250 carb problem
      By dkgg5755
      This thing came with a cheap aftermarket carb on it the problem I'm having is it won't start with choke installed into carburetor it will start and get run without it installed then bogs out after about 2 min run time I've checked timing , compression, checked valves for proper clearance , also did a smoke test for air leaks found none. 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...