Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

dmaclean

2005 Polaris Sportsman 400, Upgrading tires

Recommended Posts

I'm looking at Sun.F A033 ATV/UTV Tires 25X8-12 Front and 25X10-12 Rear.  These are on the Amazon website.  Has anyone bought these and can offer an opinion?  Also, my rear tires are 25X11-12, with the 25X10-12 size fit?

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By w_r_e
      Can anyone point me to a good set of instructions for changing front diff oil on a 1987 Suzuki LT4WD? I can almost guess which bolts are drain & fill... but I've been wrong before... 😆 
      I found some partial posts on other forums and they linked out to dead images and whatnot. Any help appreciated. 
      This thing is running pretty good, got the front brakes back to life, electric start works fine, seat cover fixed up, plastics stitched back together...
      BEFORE (last week):

      AFTER (today):

    • By Ed Zeppeli
      I have some wobble in my right rear wheel. Too much wobble.
       
      So I've torn into it and will need two bearings and two (different) seals. I'd like to get them locally if possible but need to know the number on the sides of the bearings and seals as I don't know that my bearing shop can source them by vehicle model. I'm told they're very common bearings.
       
      Any idea what the numbers are if mine end up being illegible?
       
      Thanks,
       
      Warren
    • By kgrant
      Fixing up a 1998 King Quad 300. The rear brake was locked up, and the owner tried to force it free and snapped the axle.
       
      I disconnected the brake cable, and tapped on the backing plate with a soft mallet to get the brake freed up. When I pulled off the brake drum a bunch of nasty rust water came out.
       
      Once I had the axle out, I popped the boot off so I could see the inner u joint so I could phase/synchronize it with the outer. There was a flat steel disc floating around in the boot, looks like it used to be pressed into the end of the axle. Glad I got that out of there before it munched up the joint.
       
      The book says the yokes should be aligned, I couldn't get mine aligned. They were always 7 degrees off from each other. A bit frustrating, maybe that's within the tolerance limits?
       
      But I got it all back together and it runs great.
       




       
       
    • By Ajmboy
      Just got this one and am sharing...

      Visit 4wheelparts.com Use Code: POLARISORV at checkout *Exclusive offer ends 6/17/19 at 11:59 pm CT
    • By Jeni Lynn
      2012 Rancher ES-- only when driving in 4x4 when I get to about 15-18mph there is a loud clunk in the front end and a hard downward jerk. Its almost as if its trying to downshift itself. It doesn't do it in 2 wheel drive.  I have checked the angle shift sensor and applied dielectric grease to it, changed the front end differential fluid (the old still looked good and clean) checked and adjusted the clutch. Hopefully someone can give me some more ideas. 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...