Quantcast
Jump to content

Recommended Posts

Posted

I recently bought a 1987 yamaha moto 4 200 with reverse. It’s changed hands a couple times. I’ve back tracked to the owner that might have had the owner ship. But he has passed away. I’ve been trying to pull the vin number off the frame. But it wore down and can’t make sense of it. Been on a website trying to figure it out. But can’t make sense of some of the numbers. My question is is there anywhere else the vin number would have been stamped. Or does anybody have any tricks for pulling the vin. I’ve tried several things but it is severely wore on the bottom part. Any ideas or suggestion would be greatly helpful. 

Posted

If you can't make out the VIN on the frame, it may be difficult. If the original owner or anyone after that registered it with a state authority, you may be able to do a title search. Depends how the DMV is.

59e40c81efa83_Moto4Vin.thumb.JPG.61f720cb704592f3daabcc3e0915ad24.JPG

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By docdoug72
      Has anyone had a suzuki 230 quad lock the engine up?  Its a well maintained bike, it locked up when my son was riding it. Pulled the plug, it has connected with the piston. I'm thinking the con rod let go.  I don't have a service manual.  Does the engine need to come out to check further?
    • By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • By wanrep
      View File 2019-2024 Yamaha YFZ 50 service manual
       2019-2024 Yamaha YFZ 50 service manual
      Submitter wanrep Submitted 05/04/2025 Category Yamaha ATV  
    • By wanrep
      View File 2017-2018 Yamaha YFZ 50 service manual
      2017-2018 Yamaha YFZ 50 service manual
      YFZ05YYXH
      YF05RH
      Submitter wanrep Submitted 05/04/2025 Category Yamaha ATV  
    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
×
×
  • Create New...