Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Eric poole

90 suzuki lt230 no spark

Recommended Posts

hello my dad had given me a 90 suzuki lt230 quadrunner. I brought it home and started working on it. Found couple of wires broken repaired them. Still have no spark. Started to testing I believe all tested ok. I think the cdi box is bad. The question I have is there a way to modify a cdi box. I have price a new one about 250 dollars. I really not wanting to that much in it at this time. Any help would be greatly appreciated. 

Share this post


Link to post
Share on other sites


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • bought a suzuki side by side a the scrap yard

      I just bought a suzuki side by side a the scrap yard  it says its a LT 400 and I need to know if its factory are a homemade job I'm either gonna use its part for my other suzuki atv are restore it 

      By Chomp, in General ATV Discussion

      • 2 replies
      • 101 views
    • STOLEN ATV: Stolen Suzuki Quadsport Z400 ATV

      Stolen from my storage shed on my property around 12/4/17. The post Stolen Suzuki Quadsport Z400 ATV appeared first on Stolen 911. View the full article

      By StolenATV, in Stolen ATVs

      • 0 replies
      • 26 views
    • Atc200es NO SPARK

      Hello everyone.    I am in desperate need of help as I am at my wits end with this machine.   I have a friends 1984 ATC200ES Big Red that has no spark.   Here is what has been done so far.  CDI replaced,  coil replaced, complete pulse generator assembly including the rotor/advance.    New plug. Stator checks good and has good voltage when spinning No matter what I do, I can get no voltage from the pulse generator.  I have set the gap anywhere from .010 to .020.  I have tested the ohm reading and it has 36 ohm between the blue wire and the green wire.  What is the proper way to test the pulse generator with the engine spinning?   I have been told to disconnect it from the harness and it should have approximately .7-.9 volts AC.    I have nothing.   I have also tried a 1.5V incandescant bulb across those 2 wires and the bulb doesn't even flicker. Does this have to be connected to the harness with the CDI box inplace for it to create any voltage?     It seems to me that it should create its own current when spinning where its a magnet passing a coil.    What am I missing here? Any help with this will be Greatly appreciated. Thank You Gene

      By Gene Giddings, in ATC 3-Wheeler Forum

      • 1 reply
      • 36 views
    • Suzuki from scrapyard to on the trailc

      I' bought a suzuki from our local scrap yard I got it running yet when I give it gas it lugs down muffled both rear tires slant outward are that suppose to.  That act like bearings are bad I checked bearings and there goodbeari and there   LT400fw

      By Chomp, in ATV Forums By Brand

      • 0 replies
      • 30 views
    • 2000 yamaha warrior 350 no spark

      I have a 2000 warrior with no spark bought new stator and pickup coil and still nothing tested to see if power coming from new parts and still nothing could my flywheel be bad help 

      By Beck Beck, in Yamaha ATV Forum

      • 4 replies
      • 457 views
  • Recently Browsing   0 members

    No registered users viewing this page.


×