Quantcast
Jump to content

Recommended Posts

Posted

I have an intermittent electrical problem with my 2007 Suzuki Vinson 500 auto that seem to have stumped everyone I’ve talked to so far so I’m taking it to you all. Problem is with the starter circuit, most times it works without issue but intermittently when I hit the starter button I get a loud “pop” then the whole system goes dead. I can pull start with no problem but if I try to use the winch it will kill the motor immediately. I have a 2006 I have been swapping parts from and nothing. The strange part is out of the blue the starter circuit just starts working and will do so for days or weeks on end then all of a sudden it will go offline again. Idea’s?

Posted

Have you checked your charging system? Sounds like you are loosing voltage someplace esp since you say when you use the winch.  My friend was experiencing the same problem and finally found out his charging coil was week and not supplying the proper voltage to support the bike, winch etc. 

Posted

Thanks for the feed back, when the system goes down I have hooked up a 1000 CCA automotive battery to eliminate the battery and still no crank. When I pull start and check the charging system I get 14.6V so that seems to be working. Strangest thing is out of the clear the starting system will come back on line and work well for days or weeks. The only other thing I can think of is a bad diode, the issue with that to my knowledge once a diode has failed it does not come back on line.

 

Posted

Have you changed the regulator ? Also be careful putting a big battery like that. You can blow the stator coil.  I agree with @olbooker and maybe a loose or poor connection. I would start going over every connection and don’t assume just because it’s tight it’s good. Make sure that there is no corrosion inside the connection.  

Posted

I have inspected each connection point along the wire harness and found no issues, from my 2006 Vinson I have swapped over starter relay, complete fuse block assembly problem did not follow to my 06 nor did the problem go away. I have not change out the regulator because all tests show it to be working fine. An additional piece of information that makes me think maybe a diode is bad is I am getting power feedback when I should not. I am going out on a limb saying maybe if the starter at times draws more amps than it should the neutral switch diode could cause the problem I'm not sure. The big thing I want to avoid is purchasing non returnable electronic parts and also don't want to go real deep into swapping parts over from my 06 since when the issue goes away the starting issue may go away for extended periods of time making it hard to determine if I found and corrected the problem or not. This is a true electrical gremlin. 

  • Like 1
Posted

The only test I was able to do was voltage confirmation when the motor was running, my multi tester does not have the "diode test" ability which is why I keep asking the question about the diodes. I could simply take the regulator from my 06 and swap it over to the 07 but that may be inconclusive for some time if the gremlin goes away for a while. I am looking for a conclusive test I can do with the tools I have to locate the problem if possible.

Posted

I do agree with you process of elimination does seem to be my best option given that I am fortunate to have a working 06 Vinson I can use as my free parts department. In answer to you weather related question, I wish there was a common denominator but no. This gremlin has shown up and gone away in all types of conditions. I load up at home in wet conditions drive out for a weekend of fun off load with no problem turn off the machine get my ridding gear on go to start it and nothin! Pull start it ride all day that way park it at night still no power then get up the next morning thinking I'll have to pull start again but no the gremlin has gone and I can load it up drive home unload and put it away wafer washing it and not a problem. Even my local dealer who has a 30 year+ guy as their service manager is stumped. 2 choices I have keep swapping parts in hopes I stumble across the problem or sell it which I really don't want to do. I'm not the type to dump my problem onto someone else. Thank you all for the input, if you have any other idea's send them my way I'll let you know if / when I find the gremlin.

  • Like 1
Posted

Well who doesn’t love a good mystery? I picked up a bike a few months ago that was not running. Owner said one day it works the other day nothing.  He was frustrated and could not figure it out. The price was right and I was looking for a problem child to keep me busy. After about a week of going through the coils and electrical components of this thing which tested fine,  I eventually pulled the entire wire harness out and hung it up from the garage ceiling and went through it with a fine tooth comb. I found where the harness meets the front of the frame (the neck) where the steering is connected was a worn out spot on a wire within the harness that was rubbing against the frame for a long time. And the inner conductor of a wire was exposed and rubbing against the frame grounding the harness intermittently. I re insulated the wire and the bike has been perfect.  Just one of those weird things that the previous owner could not find and I got lucky finding it. Anyway it’s going to show it’s ugly little face in time just keep at it and keep us posted. If anything comes to mind I will let you know and I’m sure someone on the site here will give you some info that had a similar problem or point you in a good direction. Good luck. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By kevinohio
      Does anyone have a copie of the owners/operators manual.the basic book that comes with the atv.i need the smaller one.i have the great big repair manual one.
    • By buriedpast
      As the title says, I've got a crankcase full of fuel / oil to deal with and figure I'll just start from the top and move through the system.  Going to start with a rebuild of the petcock and then the carb if the problem isn't fixed with the petcock rebuild.  I figure I'll go with a Moose kit unless others with experience recommend another brand (All Balls, etc.)
      Any suggestions?  Thanks in advance.
    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By LMI
      Hi all.  New to the forum & quads.  Seems like a great place full of info.
      I just recently picked up a 2005 Suzuki KingQuad LTA700.  I need a battery.  I've been reading up on conventional vs AGM types.  I have a Royal Distributing and Canadian Tire.  RD has 2 types avail for my year/Model a battery YTX16-BS CRANK $75, and BATTERY YTX20CH-BS YUASA $140.  Neither of these is the type from the manual FTZ16-BS.
      from what I can tell... I think the only difference is the capacity with the $75 unit rated at 14 AH/10HR and the $140 unit rated at 18 AH/10HR ... which is the rating in the manual for the FTZ16-BS.  How much does this make a difference for nearly x2 the cost?
      And about the models/type numbers.... what is important to know ... they all end in "-BS" but are the other details relevant or just manufacturer naming?
    • By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?
×
×
  • Create New...