Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Mary Watkiss Davis

2004 Honda Foreman what kind of oil do I need?

Recommended Posts

dumb question, I know!!!! I have a 2004 honda foreman 4 x 4 atv. There is an oil dip stick on one side and an oil hole on the other, what is it for and what kind of oil do I need.

Edited by Ajmboy
adjusted title and content

Share this post


Link to post
Share on other sites


There are no dumb questions  😉 check out this video that might help. I also edited your topic title and content and then moved to the Honda Forum.

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • By JacobSlabach
      Got a 04 Sportsman 500 that wasnt running- owner said it needed a stater and a new battery.  It ran rough (been sitting out in the weather for a while).  A friend and I started by adding a new battery and it would start barely with the choke and his hand over the air-filter.  I decided to install the new battery in the holder on the side.  we had it on the rack because the old on was still in the bike.  I tried to be nifty by turning the battery to put the terminals in an easier spot to get to, but forgot to reverse the cables too.  In a sentence, I reversed the positive and negative on the battery like a dummy.  When we discovered my mistake and corrected it, we turned on the bike, but the display did not light up and the key did not turn on the starter.  jumping the solenoid worked the starter, so we thought the solenoid just burned up when I reversed the pos and neg...  new solenoid and no difference.  what have I burned up?  Also, the shifter does not seem to do anything in the trans.  it slides back and forth like its stripped in the trans.  any help would be appreciated!!
      I think the biggest issue right now is the electrical.
    • By Jeff Taylor
      I bought a roughish Honda rancher TRX350TM3 and I am having trouble locating the vin number - I would like know year and specs as is it rough , it runs but has multiple little issues ( choke cable seems frozen , carb has sticky or ill adjusted float and leaks gas from bottom of carb , shut off valve needs new o-ring to stop leaking , ect)  just age and lack of maintenance issues , but I need to know what it is to get correct specs … I was told there would be a tag on front end of frame but I don't see one . Any help would be greatly appreciated . 
    • By CHomp DICKENS
      I broke the axle in my Honda foreman 4×4 when I went to change the axle so.done had weld it before and don't know how to git the gear off  seems the axle should slide out of the gear  not this one how do I remove the gear from broke  axle
    • By JStricker
      I'm in need of a replacement engine for my '04 400ex. Can anyone help or at least give me some direction.
      Thanks
    • By Alan Callison
      OK everybody,I need some help here please. My 4 wheeler has got a bad wheel bearing I discovered while starting a brake job. Its on the left side. I've never done one and I need some knowledge how to go about it. Am I to understand I need to pull the whole axle out to do it. I've done it once on a car about 30 years ago,lol. I keep looking around for a repair manual but they're hard to find without having to buy it. I looked here on this site but apparently Im too junior a member to be able to download one right now.Bummer!  One other question if I may.When I pulled the drum off the spindle a torrent of water poured out,the brake shoes were covered in mud along with everything else. I mean the drum had alot of water in it. The shoes were so locked up after I removed the springs I tried to rotate one of the shoes and it wasn't easy at all. I noticed whoever had the machine before myself had laid a bead of RTV around the back plate but apparently it didn't work. Isn't there some kind of gasket for this purpose. I saw it calls for a dust shield but surely this wont keep the brakes dry or will it. Thanks everybody.
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×