Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

bfh42

Typical Suzuki LT-F250 faults? Looking to Buy ATV

Recommended Posts

I am looking for an LT-F250 and I want to know if there are any common problems that develop over time so that I know what to look for when buying. Any help would be greatly appreciated.

Share this post


Link to post
Share on other sites


@bfh42 I moved your topic into the Suzuki ATV Forum, and edited your topic title a bit to Typical Suzuki LT-F250 faults? Looking to Buy ATV

Hopefully you get some good responses!

As far as typical issues, I'm not really sure because I've never owned one but try using the search to see if you find some topics of interest https://www.quadcrazy.com/search/

Share this post


Link to post
Share on other sites

I've had my 91 LT250F since new and the only issue I seem to have is that going slow makes it shift hard but once a nit of speed is obtained its s fine. Questioned it and think it's normal due to being air cooled and heat up at slow speeds.  Never did more than normal maintenance and still use it to plow. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Outkast7222
      Well been lurking for a couple years, figured its time to say hey! Been riding in MN since the early 80's been on just about anything and everything with a motor. If you are from the area hit me up! Currently riding a 2018 Sportsman XP 1000, but thinking of going to a General or possibly a Maverick Trail.
    • By dook
      I've been riding Suzuki Kingquad 300's for the last 20 years. I have 3 of them. I love the low gearing, low center of gravity, low rider position, low racks shaft drive and smooth ride, but they are getting old and I'm tired of fixing them. Best engineering of any utility quad, IMO, but the execution...build quality is not up to par with Honda, so the price you pay is lots of wrenching.
      I positively despise CVT type belt drives. My neighbor has a couple of old Hondas, Rancher and Rubicon and I admire the reliability of them. He does very little maintenance and they always run and have pulled my Kingquads home for me when they break.
      Is Honda the only company that makes ATV's that don't have CVT? I like the build quality but I don't like the high rider position caused by the vertical cylinder, the cold nature of them, having to warm up for several minutes and the plastic skid plates. I guess all modern ATV's have the same issues, though (correct me if I'm wrong).
      Been checking with the dealers, it seems Honda foot shift models are scarce. I really don't need devices/gadgets to decide which gear I need to be in. So I'm avoiding the DCT models. I must have IRS and EPS because of my age and physical condition though.
      Is it possible to get a Rancher with IRS, EPS and foot shift? The specs I'm reading show the rancher is 2" lower than the Rubicon. I'm assuming that to be seat height. With vertical cylinder design, the more you grow the engine, the higher you push the seat....at least that's my thinking.
      Any comments from the Honda experienced?
    • By mybeavah
      Let's just say there was a little fire on the old Griz and the carburetor didn't do too well. Is there an aftermarket carb on the market or do I have to go Yamaha to get this?
      Thanks in advance
      Shawn
    • By Mike Iadonixi
      Hi my son has a 1998 bearcat it won't start has plenty of charge and makes a sizzling sound any help would be greatly appreciated thank you
       
       
       
       
    • By therealjohnsmith
      I just bought these in the fall as a pair and of course they were running awesome with no problems at that time.
      One of them now will only start with starting fluid. It runs great once it's started, but absolutely refuses to start without a squirt of the good stuff.  The other one starts just fine, but dies after it gets warm. The only way to keep it running is to keep the throttle up. It won't run at an idle, and keeping it running has the throttle too high to shift.  Any ideas or suggestions are very much appreciated!!!
      Thank you,
      John from Shelley, Idaho
  • Similar Tagged Content

    • By caperwing
      I need to get a rear axle for this machine.  Are 2wd and 4wd the same axle?
      Are left and right the same axle?
      What years will fit a 1990?
      Thanks
    • By mmmPUDDIN
      I've had this machine for 2ish years, has ran great up until winter. Sometime during then, I managed to break the exhaust right before the muffler. The summer before it had a hard time idling, but we fixed it by cleaning the carb, and messing with idle. Near the end of last year, the only way for it to fire was the have full choke, and full throttle, and the engine bogged down and you had to keep on throttle for 25mins. Over winter, the throttle had dislocated, and I got it back in place. We got it running, and all was good. Spring came along, and now it doesn't start at all. A fluid is coming out of the exhaust, and I'm told it could be water from over winter. I checked the airbox, and the air filter isn't for this quad, it also is barely sucking air. There appears to be little to no compression, based on this. I'm pretty sure the engine is flooded, as the spark plug produces a spark, but is oxidized. I don't know how the previous owner treated it, or when it's last oil change was. A bolt on the engine has either oil or gas seeping through it,abd was loose. I tightened it and it consisted. The engine is basically positioned in the rear, and it needs a good clean, I don't have a pressure washer, so I can get the built on dirt off. any recommendations on how to get the beast started again?
    • By caperwing
      I just got this quad a few days ago and finally got it running. It has oil leaking and it seems to be coming out around a cylinder bolt. Not the valve cover but just below and to the rear. Is there supposed to be crush washers on that bolt? and what are those bolts supposed to be torqued at?
      Thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...