Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Liljohn2067

Yamaha 350 Wolverine unlock 4X4

Recommended Posts

I recently purchased an 01 and a 04 Yamaha 350 4X4 Wolverines. They both are full time locked in I would like to be able to lock and unlock them. Warn discontinue  

the kit they offered. I was wondering if anyone knew a fix for this, maybe a newer model Yamaha ATV parts could work on these? Or another company offers a kit? 

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Matt3
      Recently, I changed the timing chain. I lined up all timing marks and set valve lash at TDC.  The mark on flywheel was on point as well when I looked through sight hole. I started the engine and starter turned it over then it hit and stuck. I did it one more time and the same thing happened. I took everything off and saw no damage. I tried to turn it over by hand and same thing. It turns halfway or so and hits. I loosened valve lash and took crank gear off and it does the same thing. It will turn over clockwise fully but not CCW. It seems like the crank sub assembly weight is hitting the gear balancer weight. I can turn crankshaft CCW while turning the gear balancer CW and get it to go but feel it hitting something. I also can spin crankshaft CCW without crank gear on and force the engine to break past the stick. It’s not the piston.
      Please give me some suggestions thanks
    • By Wolds Alpacas
      Hello all.  I have just stripped down the carb on my YFM225 as it is not running right.
      I put it in the ultrasonic cleaner for half an hour and it has done a good job.
      Nice clean jets but when I go full throttle it backfires, and there is a lack of power.
      It also does not seem to take fuel in properly - it comes out the petcock ok so it is running freely enough, but it is not drawing into the carb.
      If anyone has any ideas I would be very grateful.
       
    • By Lellwyn Griffin
      I need to replace the starter solenoid on a 2000 Bear tracker.  The OEM is about $70 and aftermarket ranges between $10-$20.  Should I buy the OEM or is there an aftermarket brand that is good?   
    • By Ajmboy
      This is more of an informational fix I wanted to share..
      My Grizzly has been getting harder and harder to shift this winter and today was completely stuck and I needed to plow the few inches that came down this morning. First thought...oh no, tranny...but it’s winter and maybe it’s iced up. I pulled off the plastic to see what was going on and indeed I did find the drain tube iced up. 
      I took the blow dryer out and de-iced it. Quick fix, I never really thought about the shifter drain tube icing up before, shifts like new!



      FA04AC3B-4FB0-4764-AFD9-1492F5CC790B.MOV
    • By oleskool
      Looking for the service manual for a 2007 big bear 250.
      I have searched the forum for it but cant find it anywhere. If anyone has one or can direct me to the right page would be much appreciated.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...