Quantcast
Jump to content

2006 Suzuki king quad 700 fast idle

Maddmaxx

By Maddmaxx
in Suzuki ATV Forum

 Share
Go to solution Solved by Maddmaxx,

Recommended Posts

Maddmaxx Newbie

Maddmaxx

Posted
Posted

Hello guys,

not sure I have ever posted anything here but I have an issue and was hoping someone who was bored and full of information can help me.

these older King quad 700s are known for starting and stalling issues so I did the big fix, new quantum fuel pump, pressure regulator and a Kawasaki brute force .Well I screwed up, installed the new quantum pump, pressure regulator and Brute Force injector and although it did run a bit better, it still would stall out at too low of an idle so me being a dumbass decided to bring down the little brass screw on the right side of the throttle body that the butterfly touches, little did I realize this will completely throw off the TPS. In the service manual this is known as the fast idle screw, and it says do not touch this whatsoever, any advice?? , I need to know the exact thread amount on either side of this screw to get it back to factory setting, I screwed around with it a bit and as I did I adjusted the TPS into the center but now it rarely starts and when it does it idles too fast. Thanks anyone for any help, if anyone happens to have their throttlebody out or is able to pop off that little plastic cover on the right hand side a zoomed in picture would be awesome….!!..

max

  • Ajmboy changed the title to 2006 Suzuki king quad 700 fast idle
  • Solution
Maddmaxx Newbie

Maddmaxx

Posted
  • Author
  • Solution
Posted

Found a picture of the throttlebody with the screw and copied the setting, put a clean fresh Suzuki injector back in it and it runs perfectly now, thanks for all the help…

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • HTOverland
      2021 850 XTP MAXX Outlander DPS not working
      By HTOverland
      We have two 2021 850 XTP MAXX OUTLANDERS with nearly identical VINS. Both ATVS had the DPS error out the exact same week. Repair shop says need new DPS motors. How is that possible? Anyone else have DPS issues?
    • Joeguy
      91 quadrunner lt4wd shifting issue
      By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • Dsluder
      Fuel issue
      By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • Rockbottom
      2008 Yamaha Big Bear 400 will not start
      By Rockbottom
      2008 400 big bear was running now will not start
      have power to relay, in neutral, press start have power to starter but nothing happens starter does not turn
      i have good ground at battery to frame and added ground from wire harness to frame beside batter/ frame ground
      blue white wire to cdi has power with key on
      I believe the neutral lock out is working since is was before i shut it down
      if i put  it in gear and hit the start button with key on the relay does not click or send power the starter
      The 3 wires at the relay have power with key on
      What should i test next?
      thanks ahead
    • Jdeaton011989
      Timberwolf 250 starting issue
      By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...