-
Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
-
Similar Topics
-
By gpenberthy
My ranger crew 700 is hard to shift and gets locked into forward. When trying to shift into reverse we have to shut engine off. Shift then restart. Checked linkage and gears are fine. The RPMs arent really that high but did notice a little improvement when we lowered it. Did notice the throttle cable looks damaged. Could this be the issue?
-
By LMI
I wanted to share an experience and a fix.
Headed out was following a pole line, was looking for a cross track that may take me to this speckle trout looking spot on a creek. All paths and semi paths... failed. Second objective was to reach a speckle trout lake that has been recently stocked... followed 1 trail to dead end, followed second trail to dead end.... while investigating options on foot and the quad idling it died.
It wouldn't start. eventually it did... and when it did … it was essentially a pinned idle. activating the throttle did seem to speed it up but it wouldn't knock out of the racing idle. couldn't put it in gear at that idle speed. got towed out.
when I first got the quad, I ran it off a trail and buried it pretty good in the soft snow... eventually winched out. It wouldn't start. eventually did and it was fast idling. not as fast as this last time. but still fast. it eventually seemed to settle and I got it in gear and by the time I was back to the truck was acting ok. chalked it up to the bike being at a bad angle in the snow.
My investigation last year lead to the throttle position sensor TPS. how to jumper the diag block to see the sensor position on the display,. I focused on this nearly sure it was a detuned sensor or broken sensor again this time.
I tore down the front plastic and stuck my head into the TPS area to see what I could see. What I found was that the throttle body assembly had actually come out of the mounting area (not sure what it is called). the ring clamp was loose I could move it easily. Hopeful, I tore down the air intake assembly above it (air filter...etc) removed a sensor clip and a hose.
I backed off the clamp some more and was able to reseat the throttle body assembly. put some blue lock tite on the clamp screw. When I was cleaning off the air intake assembly to ensure I dropped nothing down the intake, I noticed the underside of the air intake "box" also had a clamp. this screw was completely missing.
I went to the hardware store, bought a metric replacement (brought clamp with me), seated the assembly, settled the clamp blue lock tite that as well...
quad fired right up, idled normal, idled up without hesitation and dropped right back off. Cost of solution $3.87 CND for a pack of 5 metric screws. moral of my story was don't assume an idle issue is a throttle position sensor problem... there are a number of other factors including air pressure, which I believe was my issue.
-
By aaron cesene
I have a 08 artic cat 366 4x4 fis red. Blown motor. Anyone know or where to find out what engines are compatible with this bike? Would love to upgrade if possible. My other option is to rebuild. It broke good might have pieces in jug!! So might have to come all the way apart. Help please
-
By Azrial
I just picked up a 2008 Kawasaki Teryx 750 LE 4x4 and am looking for Wench Suggestions. It was used by an old man to check his mail and only has 30 hours on it! I intend to use this on my very steep property like a small tractor. I had a old Ford 1220 Tractor and with its high center of gravity and lack of 4 wheel drive it was useless!
To the point, I am looking a wench suggestions to help my new tool do its job! Even though the front bumper is drilled for a wench, I understand that I need a wench plate and that some wenches will not fit without body mods. Does 3500 Lbs capacity sound right?
Thanks!
-
By dirtjunkie85
I have a 2008 Teryx and it has been great the only complaint I have is the engine or transmission noise inside the cab, it is a loud wine and has been this way ever sense I bought it any suggestions or products that may help quite this noise down a little??
-
-
-
Similar Tagged Content
-
By Enad Nessumsar
Forward 4x4 works fine but only 2 wheel when shifted into reverse. Can I fix that? ...How please?
Head scratching!
-
-
-
-
-
-
Recently Browsing 0 members
No registered users viewing this page.
