Quantcast
Jump to content

Recommended Posts

Posted

I have 2001 yamaha Big Bear 400 4x4,recently bought it

It came with near brand new Maxxis Zillas 27x11-12's

They are a bit too agressive for our needs..we rarely go in any deep muc and mostly just our dirt road or the woods around here in Georgia

They tear our dirt road and yard up pretty easily

Whats a good tire for our needs?

Once i figure that out,,i will either buy new or offer a good trade locally

 

forgot to add a picture of it

bigbear.jpg

Posted

I like the round cross section tyres with the small square bumps, what around here would be called a sand tyre. They are what most of the bikes used to come with standard. The bikes track and behave better with tyre contact only  down the centre line, rather than the swapping contact point you get with wide flatter cross section tyres. The wide flat tyres also chew everything up as you say. The fixed back axle alone is enough to cause slipping between left and right, without it being compounded by slippage between the inner and outer side of each tyre. Those wide flat tyrs also put more strain on the wheel bearings and suspension, which a round tyre which has it's contact point right below the steering point doesn't.

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By hengstserepair
      Howdy ya'll. I am working ona 2000 Yamaha Breeze 125. It was in rought shape when I received it and I am working through issues as they pop up. The quad had been sitting for years. I was able to get her running again, but I need your help with the following issue:
      I don't trust the transmission yet and I don't want to make problems any worse. So, I haven't pushed things hard at all. Low rpms, less than 5mph in reverse.

      Nuetral: Runs as expected
      Reverse: She seems to be driving fine at slow speeds. Going into reverse at idle is fine, coming out of reverse back into neutral won't work (the shifter is just stuck). As soon as I turn off the quad, I am able to shift around without any issue.
      Forward: It slips. It seems to only transfer power to the wheels on a smooth surface and going slightly downhill. When shifting into forward at idle, there is a clacking sounds during the transition. Shifting back to nuetral works just fine.

      Other Notable Symptoms: There was old oil in the vbelt and when I was tuning the carb, it starting blowing out of the CVT cooling vent at the front of the quad. Made quite a mess. There is positive crankcase pressure due to piston blowby, that I have not decided whether or not I am going to fix (customer budget dependant).  Since the oil was old, much darker than the new oil that is in the crankcase, I am thinking it seeped past a bad seal while it was sitting for years. The oil that was in it when I first got it had gas in it.

      Thoughts: I am thinking maybe there is an issue with the clutch. I worry about the old oil intermingling with the dry centrifugal clutch. I was thinking my next step would be to take the cover off of the clutch and inspect it.

      Let me know what you all think. Any advice and ideas is greatly appreciated. This is only the 3rd quad I have worked on and I have a lot to learn.

      Lorne
    • By Rockbottom
      2008 400 big bear was running now will not start
      have power to relay, in neutral, press start have power to starter but nothing happens starter does not turn
      i have good ground at battery to frame and added ground from wire harness to frame beside batter/ frame ground
      blue white wire to cdi has power with key on
      I believe the neutral lock out is working since is was before i shut it down
      if i put  it in gear and hit the start button with key on the relay does not click or send power the starter
      The 3 wires at the relay have power with key on
      What should i test next?
      thanks ahead
    • By Mister907
      Hi guys, I have a 2004 big bear 400. Last winter while plowing the driveway, I heard a loud pop from the left side of the engine. It continued to run as I looked for leaky fluid, but then died shortly after backing it up and won’t start now. The oil light comes on when I try to start it, no noise or anything else. 
      No blown fuses that I can find.
    • By jeffinotown
      Hey guys and gals. I've been working on my friends 2007 big bear IRS. Unfortunately after 3 different people got their hands on it and only made things worse every time.  After months of finding just crazy problems everywhere. I'm finally at the point we're its almost 100% !!! But I'm getting a short somewhere between the 4xW switch I believe. I managed to by searching the internet like a  fiend, got my hands on an official Yamaha wire harness for the year and make. But I don't have the numbered component list and to be honest. After hours of going through and making everything so it's  easy to reference. If anyone has a picture of the referenced components. I would be forever in your debt. I've spent hours marking up the blown up diagram so it will be easy, for any possible future repairs. Please and thank you. Here's a picture of what i have so far.  Unsealed it in plastic so oil and crap won't spill or get smudged. This damn things worth it's weight in gold.              Thanks Jeff                2007 Yamaha big bear 400 IRS.       YFM40FBW
    • By crankin
      I have a 1997 Yamaha Big Bear 350 4x4. It used to start right up. Then all of a sudden it wouldn't crank. I have a schematic for it so I started tracing the problem. I had no power at the starter solenoid. According to the schematic the power comes from the neutral switch and through the starter circuit cut out relay. I cannot locate the cut out relay on this machine.. If I apply power to the relay it will crank with the start button.
      The neutral switch is hard to get to with all the brackets on this thing. I did find out from all my research that if I apply the rear brake lever it will start.
      Does anybody know if the cut out relay exists and where it might be found?
×
×
  • Create New...