-
Popular Now
-
-
Similar Forum Topics
-
By exalrod
Hello All !
I am looking for a service manual and wiring diagram for a 2005 50cc Polaris Predator 4 wheeler.
Could anyone help with this?
-
By Fiend_138
Just picked up a 2014(?) Chinese quad for my kids to play around on. I can get the quad to start up, but then it dies out when we get ready to take off. Do I just keep playing with the carb, or is there something else I should be looking at?
Also, what kind of amps should I be looking for in a replacement battery?
Thanks
-
By Donaldhang92
Hi, I am new to the forum I bought a 2006 raptor 350 I test drove it. It ran decent but thought it was just due to the cold, after I got at home I rode it around and it would just die out/ lose power upon letting off from heavy acceleration or down shifting, it will just lose power and die out, I took carburetor apart cleaned it pretty well, it ran a little better at first then 1 minute into test ride she died again. Now I’m back to my shop and try to start it again and I’m left with a crazy slapping clicking noise I’ve never heard before. Let me know if you have heard this or know of the answer to my problems thanks !
IMG_7843.MOV
-
By frostydeisel
Hi everyone, this is my first post so bear with me. I recently purchased a late 80's suzuki quadrunner 250 4x4 (so i am told at least). The guy i bought it from was riding it when i showed up to look at it so i know it runs. He needed to use starting fluid and had to pull start it because the starter would just whirl when you hit the start button. He said he thinks the flywheel is bad. I dont think that is the issue. So i purchased it and took it home and was tinkering with it and i could get it started but only with starting fluid and the pull starter(which by the way is incredibly hard to pull) and when started it would run only while i kept throttling it. So i figure its a fuel problem. So i proceed to clean the petcock and give her new gas and clean the carb and spark plug. When taking off the petcock i noticed the rubber gasket was in bad condition and would need replaced. I decided to go to local autoparts store and get gas resistant gasket maker. when i get back to the quad my neighbor who was helping me(15 year old kid) had decided to take the repairs into his own hands and put it back together and get it started. That kid dogged me. Not on purpose but none the less screwed me pretty good. I didnt lose my temper and i just asked him what all he did. He said nothing just put it back together. Well kids dont always tell the truth. He kinda dropped a screw out of the carb and didnt tell me. He said he stripped the petcock screw and now couldnt remove it. He did drop the stripped screw earlier before i went to store and i found it on the skid plate. well he dropped another screw as well ive come to find out. So i tried to start it and couldnt get it to fire over at all and the starting fluid can seemed to have lost all its propellant magically when i was gone. i decide to take it back apart to where i had it before i left and see that the petcock is missing one of the filters now and that the port on it is blocked with this rusty pebble stuff. Drain out my new gas and take flashlight to the tank and see more of that crud in the bottom. i try to rinse it out but cannot do it. Then i try taking the tank off and cant. its seems i may have to remove the entire motor for that. i also see a spring and o ring on the skid plate when i remove it. very shiny spring and a clean o-ring. Notice the screw next to the idle screw is missing on the carb. checked the parts diagram and see its missing the air fuel adjustment screw. I also see why i couldnt remove the petcock screw as well. the nut that is recessed in the tank where it mounts at is pulled out a little and spins now when i try tightening it up. I could really use a manual guys. can anyone help me or give me advice on how to repair this machine? Any advice on how to operate it as well would be appreciated. I dont have any experience with this type of quad. Dont understand the decompression thingy and dont understand the starter just whirling.
-
By Arizona
And once again picked up a dead atv. This time is a Yamaha Moto 4
They don't know anything about it. I cleaned up vin best as possible and
everytime I run it it says 9th digit is wrong. The vin I punch in is ( JY43HPW08K0000690) So I think its a 1989 and
on the side of the motor is a 349 cc on cylinder so I assume its a 350 correct me if im wrong.
its been dead for about a year. Any info would be great to what it is for sure and if maybe there
is a manual here for download. 2wd, oil cooled, elect start only and batt is dead of course. Post couple of pics Thanks in advance Az
-
COMMUNITY SECTIONS
ATV FORUMS
QUADCRAZY MEMBERSHIP
Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.